For BPSK modulator fc= 70Mhz, input bit rate 10Mbps.Determine Upper and lower frequency? baud rate? Select one: a. 65MHZ 75Mhz. 10Mbaud b. 70MHZ. 8OMhz. 70Mbaud c. 65MHZ 75MHZ. 70Mbaud d. 60MHZ BOMHZ. 10Mbaud

Q: B)-The following program generates a square wave on pin P2.0. Find the output frequency? MOV R6,…

A: Here, the delay I m considering is 1ms                                             Mov r6, #0Ah…

Q: In BPSK modulation, for a zero binary input, the phase will be degrees.

A: In BPSK modulation, for a zero binary input, the phase will be........... degrees a. 0 b. 270 c.…

Q: The Excess-3 coding system is a four-bit digital coding system for encoding all decimal digits from…

A: To design a logic circuit that detects an error if a four-bit number is not a valid Excess-3 code,…

Q: 9- Şekildeki 3-bitlik sayıcı devresinde çıkışın başlangıç değeri Y = Y2Y;Yo = 111'e ayarlanmıştır.…

A:

Q: Compare two 1-bit numbers Given two input bits A and B, produce three outputs X, Y, and Z so ● ● X…

A: Magnitude comparator: Magnitude comparator has three output terminals. It checks for three…

Q: Find the value of G3, from the circuit and waveforms as below. *

A: The left most gate resembles NOT gate which alters input signal from 0 to 1 and 1 to 0 G1 and G2…

Q: Pesign Coun ter chip cel -time Digital clock Qn 4 -Bit using wi9h minimum gates

A: According to the information given:- We have to design real time clock using a 4bit counter.

Q: in hamming coding system(7,3) shown as ; 3 test bit and 7 total bit (test+data) and test bits are…

A: Given, Hamming (15,4) code . To determine the d1 to d11 values.

Q: 3. Write a HDL code for 2bit binary DECODER.

A: This is the answer to question number 3. HDL code for 2bit binary DECODER following is

Q: igure shows how a 2×2 crossbar can be implemented using 2-to-1 multiplexers. The multiplexer select…

A: We are given 2 muxes of 2:1 and select line is s whose value is 0. I have uploaded image for the…

Q: 4 bit 2's Complement Multiplier INPUT A: 4 bit 2's Complement number INPUT B: 4 bit 2's Complement…

A: What is Multiplexer? A multiplexer is a combinational circuit that has 2n input lines and a single…

Q: A combinational circuit takes a 3-bit number N as an input and generates two outputs X and Y. The…

A: Answer: Our guideline answer first three question from the firs question so we have answered first…

Q: For the diagram shown and list included select which item in the list represents area J.(enter…

A: A BCD to seven segment decoder is a circuit that converts BCD data into a format that may be shown.…

Q: Q1: (A) Represent the sequence [1001011001] as a Miller code waveform.

A: Answer waveform : -

Q: Determine the Bandwidth of a FM wave when the maximum deviation allowed is 95KHZ and the modulating…

A: Given : Modulating frequency fm = 20 KHzFrequency deviation Δf = 95 KHz

Q: The (A-O-I) is basically a : POS combinational circuit Sequential circuit SOP

A: As per our guidelines, we are supposed to answer only one question. Kindly repost the remaining…

Q: -  Calculate the bit rate given that the sampling rate is 8000 samples per second, and there are 16…

A: To calculate the bit rate, we need to multiply the sampling rate by the number of bits per sample.…

Q: Draw the output waveforms for the circuits shown below. Ch. 1 Vin 10µf Ch. 2 Vous 5V 1 KHz 20 V 100…

A: Step 1: Step 2: Step 3: Step 4:

Q: Compare two 1-bit numbers Given two input bits A and B, produce three outputs X, Y, and Z so that …

A: The question has been answered in step2

Q: Design an N-bit ALU with 4-bit ALUControl signal that fulfills the following operations.

A: Given Design an N-bit ALU with 4-bit ALU Control signal that fulfills the following operations.

Q: 4 bit 2’s Complement Multiplier INPUT A: 4 bit 2’s Complement number INPUT B: 4 bit 2’s Complement…

A: The solution is given below for the above given question:

Q: Gap between the spectral components of sampled signal in frequency domain can be increased by…

A: That gap can be termed as a sampling period Ts. Where Sampling frequency,  fs=1/Ts So, because of…

Q: Design a 2-bit magnitude compactor using 4x16 decoder and also Implement given below Boolean…

A: Magnitude compactor which refers to combinational circuit that can compares the two digital and the…

Q: c. Determine how many, and what bit adder is required to produce (five + four=nine) bits. product of…

A: A single one bit half adder would be a good choice for above given scenario. Because there are two…

Q: 9-bit binary number

A: Here is the answer which is mentioned below:

Q: Match the given baud rate and the number of bits carried by each signal unit (baud rate, bits) with…

A: 1) bit rate=baud rate x no of bits per signal             =1200*3             =3600  (Answer 1) 2)…

Q: 02: Assemble the binary bits of the "PCM" signal below into a DPSK waveform, in the case of the…

A: I will explain it in details,

Q: You are to design a circuit which takes two 4-bit unsigned numbers, A and B. Its output is a 4-bit…

A: Digital design:

Q: A circuit which connects one of 2^n data lines to one output line is defined as a* Decoder O MUX…

A: Multiplexer (MUX) :- The multiplexer is a combinational logic circuit designed to switch one of…

Q: Write a program to monitor the RB5 bit. When it is HIGH, make a LOW-to-HIGH-to-LOW pulse on RB3.

A: Write a program to monitor the RB5 bit.When it is high,make a LOW-to-High-to-low pulse on RB3.

Q: 4- Write a C code that generates 40 cycles only of waveform at 5 Hz. The output is available from…

A: void main() { int i; TRISA = 0x00; PORTA = 0x00; for(i=0;i<40;i++) { PORTA = 0xFF; delay_ms(100);…

Q: Given the following State Transition Table, the starting state 001, and the input sequence 0, 0, 0,…

A: The answer is

Q: For the diagram shown and list included select which item in the list represents area G. (enter…

A: According to the information given:- We have to  define the correct item from the list.

Q: 14. BCD numbers are applied sequentially to the BCD-to-decimal decoder in the figure. Show the…

A:

Q: 4x1 f :MUX

A:

Q: Write an asembler program that samples a 1 KHz sine signal with 16 KHz and outputs t from DACO. DACO…

A: We can write an assembler program to do the given algorithm as follows: Initialize the DACO output…

Q: the minimum sampling rate (according to Nyquist frequency) for the signal [ x(t) =2 * ? cos 600O ttt…

A: The given signal is, x(t) = 2cos6000πt + 5cos10000πt Minimum sampling rate is: S = 2 *…

Q: Nyquist sampling rate is where fm is the maximum frequency of the analog signal sampled. a. greater…

A: Nyquist sampling rate is used in specifying the sampling rate

Q: Consider the following multiplexer. With F(x,y,z) as output function. Indicate the missing values of…

A:

Q: Determine the appropriate bit settings

A:

Q: Bandwidth of x(t) = 5 cos(1000t) 500 500n cs l ow WewReopowee 57 A 2000 500/n 1000/n Ideal sampling…

A: You can predict the bandwidth in this case using the simple formula: BW = 2fm where fm is the…