For a parallel plate arrangement of the type shown in the figure below it is found that when the distance between plates is 2 mm, a shearing stress of 172 Pa develops at the upper plate when it is pulled at a velocity of 1 m/s. Determine the viscosity of the fluid between the plates. Express your answer in SI units. B Fixed plate

For a parallel plate arrangement of the type shown in the figure below it is found that when the distance between plates is 2 mm, a shearing stress of 172 Pa develops at the upper plate when it is pulled at a velocity of 1 m/s. Determine the viscosity of the fluid between the plates. Express your answer in SI units. B Fixed plate

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
A 12-mm thick steel tire has a width of 110 mm and an internal diameter of 800 mm. diameter. E = 200 GPA. It is heated and shrunk onto a steel wheel 800.50 mm in Determine the tensile stress in the tire. Determine the compressive pressure between the tire and the wheel. If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, determine its thickness.
carculate the Youngs modulus for the material of the bar shown below, The bar has an initial length of 400 mm and is measured to extend by 0.22 mm under a tensile load of 75KN, When the force is released the bar returns to its original length. The bar has the rectangular cross-section shown below. (17p) 20 mm 75 kN 75 kN 25 mum 400 mm
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F = 300 N and the cross sectional area of the rod is 200 mm2 , determine the stress in the section of copper. ... Сopper Steel 2F F 3m 2m A) 1.5 MPa В 0.75 MPa 3.0 MPа D 4.5 MPa
A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 20 cm and the wall thickness is 12 mm. If the air in the tank is pressurized to 20 MPa, determine the longitudinal stress in the wall of the tank. O 73.3 MPa O 67.7 MPa O 85.1 MPa O 94.0 MPa O 45.4 MPa
PROBLEM 3 A rubber bolt is inflated to apressure of 65kPa. At that pressure, te diameter of the ball is 240mm and the wall thickness is 1.25mm. The rubber has a modulus of Elasticity = 3.7 MPa and Poisson's ratio v=0.48. Determine the maximum stress in the ball if its stress is half that of the cylinder.
M A cylinder of outer radius R2=100 mm is fitted on another cylinder of outside radius R₁=85 mm with thickness t=30 mm, as depicted below. If the (tensile) maximum hoop stress at the interface between the two cylinder is 90 MPa, solve the following questions (E=105 MPa and v=0.15). === R₁ What is the radial stress between the cylinders? What is the shrinkage allowance at the interface? ( M R₂ )
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN