13. As shown in the figure, a homogeneous 100-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G = 42 GPa. Compute the maximum shearing stress in each spring using A.M. Wahl formula. %3D Phosphor Bronze Steel Steel 3 m 5 m 100 kg

13. As shown in the figure, a homogeneous 100-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G = 42 GPa. Compute the maximum shearing stress in each spring using A.M. Wahl formula. %3D Phosphor Bronze Steel Steel 3 m 5 m 100 kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F1 (kN) 30 mm 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as shown. Determine the principal stresses, principal planes, and maximum shearing stress and show the stresses on an element (a) at point H, (b) at point K.
(c) A vertical tie fixed rigidly at the top, consists of a steel rod 2.5 m long and 20 mm diameter encased throughout in a brass tube 20 mm internal diameter and 30 mm external diameter. The rod and casing are fixed together at both ends. The compound rod is suddenly loaded in tension by a weight of 10 kN falling through 3 mm before being arrested by the tie. Calculate the maximum stress in steel and brass. Take Es = 200 GPa and Eg = 100 GPa.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 21 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 15 ksi, determine the minimum diameter d₁ required for rod (1). (1) (2) A O 1.410 in. O 0.936 in. O 1.843 in. O 1.132 in. O 1.335 in. F₂ B C d₁ -d₂
A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the figure. For bronze, G = 30 GPa; aluminum, G = 28 GPa, and for steel, G = 83 GPa. Determine the maximum shearing stress developed in each segment. TC = 17x100 N-m ; TD = 7x100 N-m Te A Bronze Steel B 25 mm 25 mm 2 m 2.5 m To C Aluminum D 50 mm 2m
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
(c) A shaft composed of segments AC, CD and DB is fastened to rigid supports and loaded as shown in figure. For bronze, G = 35 GPa, for aluminium, G = 28 GPa, and for steel, G = 83 GPa. Determine the maximum shearing stress developed in each segment. TA Tc = 300 Nm T A Bronze 25 mm TD=700 Nm Aluminium TD 50 mmo 2m-2 m+ Steel B 25 mm -2.5 m T TB
A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the figure. For bronze, G = 35 GPa and for steel G = 83 GPa. Determine the maximum shearing stress developed in each segment. Solid Shaft STEEL A Tc = 290 N-m 25 mm Ø -1 m Solid Shaft BRONZE 40 mm Ø -2 m Td = 550 N-m Required Values: (Units in MPa) Tst1= Thr=. Tst2 Hollow Shaft STEEL -2.5 m B D-60 mm d=50 mm For segment DB
A helical spring composed of 20 turns is fabricated by wrapping wire 10mm in diameter around a forming cylinder 150mm in diameter. Compute the maximum load that the spring can carry if the total elongation is limited to 90mm and the allowable shearing stress is 90 MPa. G=28 GPa.
(5): The bell crank shown in Figure, is in equilibrium, a) Determine the required diameter of the connecting rod (AB) if its axial stress is limited to (100 MPa). b) Determine the shearing stress in the pin at point (D) if its radius the (20 mm). B 200 mm 240 mm D 60 30 KN 1
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 280 MPa, determine the minimum diameter d₂ required for rod (2). 80 KN d₁ O 18.2 mm O 28.7 mm O 24.6 mm O 30.2 mm O 21.7 mm 140 KN 140 KN B (2)
The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. |800 kN/m +100 mm -100 mm A B 125 mm I800 kN/m Answer: 0A = 0c = 189 MPa, oB 21.4 MPа