For a laboratory consolidation test on a clay specimen (drained on both sides) the following results were obtained: Thickness of clay soil= 25 mm; P1 = 50 kPa; P2 = 120 kPa; e1 = 0.92; e2 = 0.78; Time for 50% consolidation= 2.5 min. Tv = 0.197. Determine the coefficient of compressibility in m2/kN.include fbd pls

For a laboratory consolidation test on a clay specimen (drained on both sides) the following results were obtained: Thickness of clay soil= 25 mm; P1 = 50 kPa; P2 = 120 kPa; e1 = 0.92; e2 = 0.78; Time for 50% consolidation= 2.5 min. Tv = 0.197. Determine the coefficient of compressibility in m2/kN.include fbd pls

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.20P

See similar textbooks

Similar questions

The table below contains data obtained from 2 CU triaxial tests on similar clay specimens. Specimen no. Cell pressure during consolidation (kPa) Deviatoric stress at failure (kPa) 269 Pore water pressure at failure (kPa) 264 400 379 1 2 462 689 Calculate the cohesion, c (kPa) of the clay soil in terms of total stress. Enter answer to 1 d.p. and don't enter units.
A triaxial compression test was conducted on a saturated soil sample to determine its shear strength parameters: effective cohesion (C') and effective friction angle (O'). The confining pressure used during the test was 30 psi. The deviator stress on the sample at the time of failure was 40 psi. The porewater pressure measured at the time of failure was 5 psi a) The figure below shows the stress conditions on the sample at the time of failure. Provide the values of total stresses, o1 and oz on the sample. Total horizontal stress, o3 (psi) = (Report to the nearest whole number, i.e. no decimals) Total vertical stress, o1 (psi) (Report to the nearest whole number, i.e. no decimals) %3D b) The figure below shows the effective stress Mohr's Circle for the above soil sample at failure. What are the values of effective normal stresses at points A and B?
3. In a drained tri-axial test, a specimen is confined under pressure and axially loaded until failure. The failure conditions of the specimen are analyzed for shear strength. What is the value of the minor principle stress? Half the value of the major principle stress Twice the value of the major principle stress . The same as the confining pressure The same as the cohesion value ● ● ●
Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.
a) A CU triaxial test was carried out on a silty sand soil sample. The cell pressure was equal to 200 kPa. At failure the deviator stress was equal to 410 kPa and the pore pressure was equal to 73 kPa. i) Assuming that the cohesion intercept is equal to 0, calculate the friction angle of the soil. ii) If the friction angle was equal to 35°, calculate the cohesion intercept of the soil. iii) Calculate the angle of the failure plane relative to the horizontal plane for the soil shear strength parameters in Question 4 a i and 4 a ii.
A direct shear test was conducted on a dried sand sample in a test box of 60mm x 60mm normal load of 400N. The soil sample failed at an applied shear force of 250N. a. Determine the shear strength parameters of the soil. b. Estimate the required shear force to cause a shear failure under a normal load of 600N. (Show all working calculations.)
5. Triaxial tests were conducted on undisturbed samples of clay under CU conditions. Data from the test are summarized in the Table 2. Graph the Mohr's circles and draw in the failure envelope. Determine the strength parameters c' and ("? Table 2. Data from CU Tests Cell pressure (3 (kPa) 359 719 719 Test A B C Pore pressure at Failure u (kPa) 339 585 451 Deviator Stress at Failure. (1-(3 (kPa) 539 731 1015
9. A consolidated drained test was carried out on a sandy clay under a cell pressure of 250 kPa. A constant back pressure of 120 kPa applied throughout the test. The dimensions of the sample were 76 mm x 38 mm. Addional test data recorded at failure were: Load transducer force = 368 N 3 Measured change in volume = 2.42 x 10 m³ Axial deformation = 2.05 mm Determine the major principal stress, o, at failure. (455 kPa)
Part #2 Effective Stress (kPa) Void Ratio (%) The following are the results of laboratory consolidation test conducted on clayey soil sample. Determine, graphically, the compression and recompression indices, Cc, C, of this soil. Using Casagrande's method, determine graphically the preconsolidation pressure. 0.891 54 0.866 107 0.841 214 0.802 429 0.737 858 0.653 1716 0.560 3432 0.467
4.15 The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 6 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 (а) Determine the liquid limit of this clay. (b) If the natural water content is 38% and the plastic limit is 23%, calculate the liquidity index. (c) Do you expect a brittle type of failure for this soil? Justify your answer.
During an oedometer test on a specimen of saturated clay, the thickness of the specimen decreased from 19.931 mm to 19.720 mm under an increment of stress from 200 to 400 kPa which was maintained for 24 hours. The stress was then removed from the specimen, its thickness was measured as 19.842 mm, and its water content determined as 26.8%. Taking Gs of the particles to be 2.70, calculate the void ratio before and after the application of the stress increment, and the coefficient of volume decrease (m,) for this stress range. (Ans: e,= 0.731, ez= 0.713, m, = 0.052 m²/MN)
A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: O a. 0.42 b. 0.61 c. 0.79 d. 0.57 It is the densification of soil by removal of air which require mechanical energy. Select one: a. solidification b. consolidation C. compression d. compaction What particular sand is ideal for field density test using sand cone method? Select one: O a. clean sand b. Ottawa sand c. Owatta sand d. white sand