For a frame shown, a 4442 N load is acting on a member ABD at D. If the allowable material shear stress for is 44 MPa, determine the required diameter (rounded off to the nearest 2.5mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12mm and that of member DE is 16 mm, determine the maximum bearing stress at C.

For a frame shown, a 4442 N load is acting on a member ABD at D. If the allowable material shear stress for is 44 MPa, determine the required diameter (rounded off to the nearest 2.5mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12mm and that of member DE is 16 mm, determine the maximum bearing stress at C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

T'he pin is made of a material having a failure shear stress of Tail = 100 MPa. Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of F.S. = 2.5 against shear failure. %3D 80 kN
Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
0.16
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC Is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60 mm outside diameter and 30-mm inside diameter Determne the maximum shearing stress in the aluminium in MPa if a torsional load ot 4000 N m is applied at B. Ends A and Carerigidly damped. 45 mm 60 mm 30 mm 12m
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 18 ksi, the normal stress in brass rod (2) must be limited to 23 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 6 kips, R = 16 kips and S = 23 kips. SI (1) VQ (2) (3) A Answer: F₁ = B R C D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A. i kips.
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
13
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths