Flow Rate. A pipe with a radius of 2.1 [cm] leads to the second-floor bathroom 7.0[m] above. When the flow speed of the inlet pipe is 1.2[m/s], what is the volume flow rate in the bathroom? Select one: ○ 1.66 × 10-³[L/s] O 6.60 [L/s] O 5.29 [L/s] O 1.66 [L/s]

Flow Rate. A pipe with a radius of 2.1 [cm] leads to the second-floor bathroom 7.0[m] above. When the flow speed of the inlet pipe is 1.2[m/s], what is the volume flow rate in the bathroom? Select one: ○ 1.66 × 10-³[L/s] O 6.60 [L/s] O 5.29 [L/s] O 1.66 [L/s]

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 2.60 kg steel gas can holds 25.0 L of gasoline when full. What is the average density (in kg/m3) of the full gas can, taking into account the volume occupied by steel as well as by gasoline? _______ kg/m3
A horizontal pipe carries a smoothly flowing liquid of density of 1290 kg/m³. At Locations 1 and 2 along the pipe, the diameters are dj = 6.79 cm and d2 = 2.79 cm, respectively. Is the flow speed at Location 2 higher or lower than the flow speed at Location 1? d Location 1 Location 2 d2 O higher cannot tell from the data lower The flow speed at Location 1 is 1.87 m/s. What is the pressure difference AP between Location 2 and Location 1 (including its sign)? Ignore viscosity. AP = Ра
The suction pressure of a pump reads 540 mm Hg vacuum. What is the absolute pressure in kpa? 40 3.3 60 29
An airplane flies on a level path. There is a pressure difference of 618 Pa between the lower and upper surfaces of the wings. The area of each wing surface is about 100 m2. The air moves below the wings at a speed of 80.5 m/s. A.)Estimate the weight of the plane. B.)Estimate the air speed above the wings. Density of air is 1.29 kg/m3.
The water pipe shown in the figure has at its intake a cross sectional area of 0.74 m² and a water flow speed of 0.4 m/s. The outlet of the pipe has a smaller cross-sectional area and a water flow speed of 9.5 m/s. The intake is at a distance D= 180 m above the outlet. D Pw 10 kg/m³: g-9.8 m/s² Question 9: The cross-sectional area of the outlet is A. 17.575 m² B. 0.031 m² C. 0.057m² D. None of the above A B C D Option O O O Question 10: The pressure difference Poutlet-Piniet is A. 1718955 Pa B. 1764000 Pa C. 45045 Pa A B Option O O Intake P Outlet D. None of the above C D O
Water is flowing in the pipe shown in the figure below, with the 8.10-cm diameter at point 1 tapering to 3.05 cm at point 2, located y = 11.0 cm below point 1. The water pressure at point 1 is 3.20 x 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 (b) point 2 m/s m/s
At the entrance point in a pipeline, the water’s speed is 25.5 [m/s] and the gauge pressure is 3.50×10^4 [Pa]. Find the gauge pressure at the exit point, 10.0 [m] lower than the entrance point, if the water here is flowing at 8.81 [m/s].a) 4.19 x 10^5 Pab) 1.33 x 10^5 Pac) 2.23 x 10 ^5 Pad) 3.21 x 10^5 Pa Please find the right answer and show solutions!
The entrance opening of a horizontal pipe has a radius of 6 cm and water is flowing at .35 m/s. The pressure at opening is 18.5 n/m2 and changes to 23.0 N/m2 at the exit. What is the area of the exit opening?
A liquid is flowing through a horizontal pipe whose radius is 0.0301 m. The pipe bends straight upward through a height of 8.80 m and joins another horizontal pipe whose radius is 0.0726 m. What volume flow rate will keep the pressures in the two horizontal pipes the same? Number Units 202
2. Set the parameters of the simulation as below. D = pipe diameter P = pressure u = fluid velocity Din = 5.0 cm Pin = 107 kPa Uin 3. = 3.8 m/s Az = 7.4 m Dout = 6.4 cm = 39 kPa out = 2.3 m/s u out Directions Change in height Outlet pipe diameter Inlet pressure Inlet velocity Details Display: Fluid properties Energy About 7.4 m 6.4 cm 107 kPa 3.8 m/s density p = 1000 kg/m³ and g = 9.8m/s^2 Using the simulation, verify using Bernoulli's equation if the outlet velocity and outlet pressure value in the simulation is correct?
A hall has a volume of 240 m3. An air-conditioning system is to replace the air in this hall every thirty minutes, using ducts that have a square cross-section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is 6.0 m/s.
10. In an industrial cooling process, water is circulated through a system. If water is pumped with a speed of 5.60 m/s under a pressure of 6.20 x 105 Pa from the first floor through a 3.60-cm diameter pipe, what will be the pressure on the next floor 3.70 m above in a pipe with a diameter of 2.30 cm? Pa 7 2 Z @ 2 W S X H command # w = 3 E D C C $ 4 R LI F % G Search or type URL 5 V. T 1332 19 G 6 MacBook Pro B Y H & 7 N U J * 00 8 M - K 1113321 ( 9 V I < O 10 L command P ^ I Y : ; option { [ ? I + = FF A