flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b

Q: Q- fluids, The Coefficient of discharge of a orifice meter is 0.97. The time taken by fluid to cover…

A:

Q: A fluid of density 840 kg/m and dynamic viscosity 1x103 Pa.s flows through a pipe of diameter 21 mm…

A: Given:-ρ=840 kg/m3μ= 1×10-3 Pa.sV=1.1m/sd=21mm=0.021mTo find:-Reynlods number, Re

Q: 1. A pipe of 100 mm internal diameter carries water at 20°C, which has a density of 998 kg/m³ and a…

A:

Q: Calculate the Reynolds Number of the flow.

A: Given: Diameter (D) =50 mm =0.05 m Velocity (V) =8 m/s viscosity (μ)=1.14×10-3 Ns/m2 To determine:…

Q: As an engineer, you are setting up an experiment to measure the airflow rate in a duct. Choose a…

A: Venturimeter is one of the well known device for flow rate measurements. Reason : It involves less…

Q: Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is…

A:

Q: Pump A 10 m Branch 2 Branch 1 20 m from point B to pump Branch 3 B 5 m

A:

Q: This statement is for Questions 4-6: An engineer claims that flow of SAE 30W oil, at 20°C, through a…

A: An engineer claims that flow of SAE 30W oil, at 20°C, through a 5-cm (0.05 m)-diameter smooth pipe…

Q: A patient receives IV fluid through a needle of radius 0.200 mm and length 2.0 cm. The density of…

A:

Q: Consider flow of blood in the microvessels of the body, assuming Poiseuille’s law holds and that the…

A: Solution: Given Data: Consider flow of blood in the micro-vessels of the body, assuming Poiseuille’s…

Q: (b) Fluid flow through a horizontal circular pipe of inner radius of 2 cm with centerline velocity…

A: The Reynolds number of the flow is The flow is laminar.

Q: An oil with a dynamic viscosity of 0.8 Pa.s and specific gravity of 0.9 is flowing through a…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Liquid A(sp gr = 0.95) at a temperature of 29°C is flowing at a rate of 120gal/min in a pipe with an…

A:

Q: It is desired to determine the surface tension of a particular fluid using a capillary-rise…

A: Given data  capillary rise (h) = 30 mm = 30*10-3 m diameter of tube (d) = 0.5 mm = 0.5*10-3 m…

Q: Calcuale the viscosity of the oil if the  sp. gr. 0.8 is measured by a capillary tube of diameter 50…

A: Data given-  Specific gravity = 0.8  d = 50 mm = 0.05 m  L = 3 m  h = 0.6 m of water  m• = 50 kg/min…

Q: p1: oil with viscosity (2n10 N.s/) and densily af (850 kg) is Pumped along astraight herizon hal…

A: Given, Density of oil, ρ=850kg/m3Viscosity of oil, μ=2×10-2 (Ns/m2)Discharge,…

Q: Oil should be transported through a 2 (km) long pipe. The tube is made of stainless steel and has a…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: pipe with a velocity of 20mm/s. What is the pressure difference between the point of entry to the…

A:

Q: Fluid originally flows through a tube at a rate of 110 cm3 /s. To illustrate the sensitivity of flow…

A: Given data Volume flow rate, Q1 = 110 cm3/sPressure drop, Px1 = 2.5Radius of tube = rx1 = 0.14Length…

Q: The pressure difference between two points in pipe due to turbulent flow depend on velocity,…

A: ∆P=fV,D,μ,ρ,ε,L

Q: Consider the setup shown below, with a valve to adjust the flow of a fluid to an orifice meter…

A: Given data: Liquid acetone density ρa=0.791 g/cm3 rotameter calibration equation' V=1.56 R…

Q: (Pipe Radius = 25mm) (5 =Local head loss coefficient) 1. Calculate the & values for Valve and Elbow.…

A: In pipe or tube system components, minor or dynamic pressure loss can be stated as ∆P…

Q: (b) An oil with dynamic viscosity of 0.8 Pa. s and specific gravity of 0.9 is flowing through a…

A: It isn't not difficult to track down a great deal of data on the distinctions among dynamic and…

Q: A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter…

A:

Q: A 15 m building use cast iron pipes in their piping system. The water tank located on the top of the…

A:

Q: A Venturi meter is being used to determine the flow of soybean oil at 65 °C in a pipe. The…

A: Ans Given Now calculate the inlet cross-sectional area of pipe as Again calculate the outlet…

Q: Pravinbhai

A: The objective of the question is to calculate the Reynolds number for a fluid flowing through a pipe…

Q: On a single plot, plot three curves that show the relationship between the pressure generated by the…

A:

Q: An 18-kg slab slides down a 15° inclined plane on a 3-mm-thick film of oil with viscosity of…

A:

Q: Fluid is moving at rate of 3m/s in a chamber of a 12inch positive displacement flow meter, if the…

A:

Q: (b) Fluid flow through a horizontal circular pipe of inner radius of 2 cm with centerline velocity…

A: The Reynolds number of the flow is The flow is laminar.

Q: Oxygen reaches the veinless cornea of the eye by diffusing through its tear layer, which is 0.60-mm…

A: Given:To find:(a) Average time taken by oxygen molecule through the tear layer.(b) Average time…

Q: A fluid of density 840 kg/m and dynamic viscosity 1x103 Pa.s flows through a pipe of diameter 21 mm…

A: given datadensity of fluid (ρ) = 840 kg/m3dynamic viscosity = 1×10-3 Pa.sdiameter of pipe = D = 21…

Q: 3. Compute the friction head loss in meters of a fluid at a certain condition (S.G.-1.101) that is…

A:

Q: Discussion 1- Indicate the factors affecting the Reynotes number (Re). 2. The limits are gaved to…

A: 1. The Reynolds number is calculated as  : Re=ρVDμhere,ρ is the density of fluid in kg/m3V is the…

Q: Glycerine, with a viscosity of 0.09 kg/ms and density of 1 260 kg/m³, is pumped at a flow rate of 20…

A: