Find the largest force (in N) that can be applied in in the clevis shown if the diameter of the bolt is d = 37 mm and the shearing strength of the bolt is s = 373 MPa. Round off the final answer to two decimal places.

Find the largest force (in N) that can be applied in in the clevis shown if the diameter of the bolt is d = 37 mm and the shearing strength of the bolt is s = 373 MPa. Round off the final answer to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: efore a load is applied, a rigid bar is fastened to two vertical rods. Calculate the vertical…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness…

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

Q: A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1…

Q: imple beam of length (L) subject to a concentrated load (P), shown in figure, Find - 1. Max.…

A: Given:- L=3m P=2.6kN A=29mm B=150mm C=38mm D=130mm F=1000N To find:- a) Max. compression and tension…

Q: 155 mm. Determine the minimum clamping fo when T₂ = 60°C is at least 2.0 kN. a

Q: Determine the force acting on members BE, FH, and HK. . Final answer must be rounded to the nearest…

A: Determine the force acting on members BE, FH, and HK.

Q: For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts…

Q: The pin support at A has a double-shear steel bolt as shown. Determine the required diameter of the…

Q: Solve the plate shown in the figure, Include fbd on solutions

Q: The bolt in the figure below is 1 in. in diameter. If the load P is 10 kips, determine the average…

A: Given-Bolt diameter= 1 inchLoad, P=10kips

Q: Consider the beam and loading shown. NOTE: This is a multi-part question. Once an answer is…

Q: A plate is used as a bracket and is attached to a column flange as shown in the following figure.…

A: The structural junction known as a bolted connection. To link steel constructions, they are…

Q: strain in the tension bars equal to 0.004 and in the design process use 60% of this rho max.…

A: Given : DL = 10 kN/m LL = 8 kN/m UDL & 15 kN/m UVL 8 m length fc = 21 MPa and fy = 276 MPa

Q: The compound shaft, shown in the figure, is attached to rigid supports. For bronze (AB) d = 75mm,…

Q: SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25…

Q: A 26-mm-diameter steel [E = 190 GPa; a = 11.8x10-6/°C] bolt is used to connect two rigid parts of an…

Q: Problem 4- For the axial forces shown, determine the final locations of points B and C with respect…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the nominal strength for tensile yielding in the gross section. 1. B. 429.67 KN D.390.10…

Q: 3 m Reactions @A Ic Ax = A₁ = MA = Internal Loads @C V = M= N = 3 m ts) s) 8 kN/m 3 m Force lagram…

Q: Determine the bolt diameter if the shear stress is 150 MPa and the bearing stress is 337.50 MPa.

A: The values and diagram given in the question are as follows: Shear stress(t)=150 MPa Bearing…

Q: Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum…

A: Given that: E = 200 GPa

Q: Ac-beam is subjected to the loads shown. The dimensions and loads of the c-beam are given below. P=5…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: The group of 6-bolts connection subjected to eccentric load P=30 kips as shown in figure. The…

A: Given a bolted assembly, it is required to find the maximums hear force.

Q: A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1…

Q: 1. Determine the maximum shear W = 12 KN/m 4m 2m and moment of the beam loaded RI R2 shown.

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: T2 T1 T3 60° 40°

Q: a) A610×229 UB 125 tension member of S355 steel is connected through both flanges by 20 mm bolts (in…

A: Given data 610×229×125 UKB tension memberConnected length 20 mm boltsNt, Ed=4000 kN Considering…

Q: The rod supports a weight of 390 lb and pinned at its end A. It is also subjected to a couple moment…

Q: The change in diameter of the large steel bolt is carefully measured as the nut is tightened.…

A: Given ; initial dia d = 50mm E - 190 GPa To FInd - Internal Force in the bolt if the dia is observed…

Q: Problem 3 & 4. For the following built up beams, calculate the shear flow q (lbs/in or kips/in) at…

Q: Consider the girder and the moving loads shown in (Figure 1). Suppose that P = 80 kN. Figure 1 A 6m…

A: Beam:Rolling loads:To find:The maximum live bending moment at C caused by the moving loads.

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given data The plate is fastened to the fix member by three 10 mm diameter rivets

Q: Determine the moment of each force about the bolt located at A (Figure 1). Take FB = 45 lb. Fo= 30…

A: Given:- FB = 45 lb FC = 30 lb To find:- Moment about A due to force FB Moment about A due to force…

Q: In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm…

A: Lap joint: When one plate is overlapped on the other plate and both the plates are riveted by a…

Q: A 23-mm-diameter steel [E = 200 GPa; a = 12.5×10¯6/°C] bolt is used to connect two rigid parts of an…

A: Given Diameter of steel =23mm E=200GPa α=12.5×10-6/°C Bolt length(a)=175mm T1=21°C; T2=56°C Force…

Q: Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft D…

A: Mass of crate = 550 lbTo determineThe normal force at FThe shear force at FThe bending moment at…

Q: problem

Q: The bolt in the following figure when tightened, we measure a 8=13µm decrease in the bolt diameter…

Q: A plane truss has a downward applied load P at joint 2 and another load P applied leftward at joint…

A: Answer Given data A plane truss has a downward applied load P at joint 2 and another load P…

Q: A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. www…

Q: 3 $5 3.S 2.5 5-2) tsts tugt o 1S cm Scm

Q: To Ko L 24 3L Consider the structure shown left. The cross- section of the shaft is a circle, and…

A: Given Data: Conical shaft having circular cross section. External torque equal to T0 at 3L is…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The lap joint shown in Fig. is fastened by three rivets. If the shearing stress in the rivets and the bearing stress in the plates are detailed in the Table below. Calculate the load P and diameter of the rivets. Assume the applied load is uniformly distributed among the three rivets. P Plate Ob thickness (t) (MPa) MPa mm 125 98 20
Consider the figure 1 below: 3-25mmø bolts are used to fasten a plate to a steel beam a) Determine the average shearing stress caused in each bolt by the 30kN loads. b) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 6OMPA. 30 kN 150 300 200 P 30 kN 75 Foot
AWTHE FIGURE. DVIDE COMPLETE SOLUTION. T FOLLOWING INSTRUCTION VWILL GET ZERO, cermine the reaction at supports and compute the force in members: ca, cd, and cf u may use any method.) ulate your final answers: MBER// FORCE, KN/ COMPRESSION OR TESNSION 5m 30 40KN 5m 5m 6m Show all 99
Please explain those marked in red, thanks!
Three wood boards, each 4 in wide, are joined by the 3/4-in-diameter bolt. If the working stresses for wood are 800 psi in tension and 1500 psi in bearing, find the largest allowable value of the force P. P 1 in. P 2 in. P 1 in. in. 4
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
The control arm is subjected to the loading shown. The allowable shear stress for the steel pin is τ = 10 ksi. Determine the required diameters of the steel pins at A and C. Write your final answer to the nearest three decimal places.
The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force (P) acting on the member is 25 KN, determine the maximum shearing stress developed within among the bolts. Strap Plate Member Plate P← P (9
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
The five-bolt connection must support an applied load of P = 114 kips. If the average shear stress in the balts must be limited to 10 ksi, what is the minimum bolt diameter that may be used for this connection?