Use the moment-area method to determine the slopes and deflections at points B and C of the beam shown 50 kCB-9 ftft--9 ft--18 ft-El = constantE = 29,000 ksiI = 4,000 in.4%3D

Answered: 50 k C B -9 ft ft- -9 ft- -18 ft- El =…

Engineering

Civil Engineering

50 k C B -9 ft ft- -9 ft- -18 ft- El = constant E = 29,000 ksi I = 4,000 in.4 %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a. Determine the force in each member uf the real and the virtual truss shown above. b. What is the…

A: Find reactions:Take moment about Right support:∑ MA=0Cy(3)-100(4)=0Cy=133.33kNTake moment about…

Q: Determine the deflection at C using virtual work method. 30 kN/m B C 6 m -4.5 m- El = constant E =…

Q: HW 1: Determine the deflection at point D of the beam shown in Fig. below by the virtual work…

Q: b) Find the vertical deflection at the hinge of the following structure using the virtual work…

Q: j: Using the conjugate beam method to determine rotation at 8 & deflection at C 40 kN/m 20 KN 150 KN…

Q: Q3/ For the beam show in fig. Determine the vertical deflection at point D, using virtual work…

A: Consider the free body diagram as; Calculate the reactions as; RA=RE=1502RA=RE=75 kN Moment…

Q: Determine the slope and deflection at point C of the beam shown by the direct integration method and…

A: Overhang beam with two point loads NOTE : The question is solved by direct integration method…

Q: Determine the deflectiom at the free end on the beam using conjugate beam method. The homogeneous…

Q: Q2) Find the vertical detlection at D and rotation at B in terms of El by the unit-load method for…

A: In the virtual load or unit load method, a unit load is applied on the point where deflection and…

Q: Specify the maximum deflection of the beam shown. El is constant. E = 200 GPa, I = 15(105)mm c) Use…

A: Hello dear this is the solution of your problem The answer is found to be Maximum deflection is…

Q: solve for the formulas of the maximum slope, maximum deflection, and their respective location, for…

Q: The overhang beam shown below has a non-prismatic section. Given E = 29000 ksi, I = 3000 in¹.…

A: Given: A non prismatic overhang beam Required: Rotation at C and deflection at D using conjugate…

Q: 3/4 t

A: Method of superposition is the method by which we can find the slope and deflection at any…

Q: B A 1. C

Q: For the beam shown, determine the deflection at D using the virtual work method. Please be clear…

Q: For the beam shown, determine the deflection at D using Castigliano’s second theorem. Please be…

Q: Determine the deflection at the midspan of the beam shown below. 10 kN 5 kN/m Art 21 THIT B 1 m 1 m…

Q: Determine the deflection at point B for the beam shown using the direct integration method. -6 ft-…

Q: Determine

Q: Determine the smallest cross-sectional area A for the members of the truss shown, so that the…

Q: Q.3 Determine the slope at A and deflection at C in the beam shown below: 11KN/m 4m C 2m 10KN 3m B

A: We have to determine the slope at A and deflection at C

Q: Use the superposition method to determine the slopes and deflections at points B and C of the beam…

Q: Calculate the deflection at the left of the midpoint using the conjugate beam method. Мо L, EI L, EI…

Q: Find the deflection at point D using a virtual method.

A: Given Data Find the deflection of point D using virtual load method.

Q: 270 kN 45 kN/m В 3 m 3 m 3 m El = constant E = 200 GPa I = 1665x10°mm

Q: Calculate the slope and deflection at the free end of the cantilever beam shown in figure using…

A: Apply standard results for each case

Q: Determine the maximum deflection for the beam shown by the moment-area methoc 135 kN в -2.5m- -5 m…

A: E=70GPa I=210*106 mm4 To find maximum deflection

Q: Use the conjugate-beam method to determine the slope and deflection at point B of the beams.

A: The given figure is shown below:

Q: From the figure below determine the deflection at the overhanging section. a. Using Double…

Q: Using MOMENT-AREA Method for deflection analyze the beam below 25KN 10KN/m A El-120000KNM^2 B…

A: Given beam:

Q: 3. Find the deflection at the midspan of the beam loaded as shown. The beam supports a uniformly…

A: The given beam is statically determinate beam and can be analyzed using the equations of equilibrium…

Q: 30 kN 2.00 6.00

Q: a) Use the principle of virtual work to determine the rotation at Support B. (The postive direction…

A: Given: q = 14KN/m P = 35 KN Required : Rotation at support B

Q: Determine the deflection at the midpoint of the beam using virtual work.

A: Draw free body diagram Calculation of support reaction RA+RB=12×250×7RA+RB=875N

Q: 90KN A В 5.00m 3.00m

Q: 1p kN/m 20 kN 3m- 8 kN- D 6 m 4.

Q: A rigid beam BC is suspended by links AB and CD. Determine the deflection at point E if the areas…

A: Given: The modulus of elasticity is 200 GPa. The area is 150 mm2.

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

Use the moment-area method to determine the slopes and deflections at points B and C of the beam shown

50 k
C
B
-9 ft
ft-
-9 ft-
-18 ft-
El = constant
E = 29,000 ksi
I = 4,000 in.4
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem: Determine the deflection specified in each of the following beams. Use only one method to solve for each. You can choose which method to use in each beam, as long as all three must be used in one of the beams. Assume constant El. Use E = 200 GPa and I = 800 x 10 mmª for all beams. 3.) At the location of the interior hinge TAA 3m B 8m 10 kN/m 9 m 9 m 6m P = 229 KN ·100 KN.
4. For the beam loaded as shown, find the slope and deflection at point B. Use E = 200,000 MPa and I = 10 x 106 mm4. Use conjugate beam method CS Scanned with CamScanner 30 kN/m -5.0 m- bb -2.0 m
3. Use the method of virtual work. Determine the smallest cross-sectional area A required for the members of the truss shown, so that the horizontal deflection at joint D does not exceed 10 mm. 50 KN 50 kN c↓ 100 kN EA-constant E-70 GPa
3. Use the moment-area method to determine the slopes and deflections at points B and C of the beam shown. 6m B 3m 250 KN 3m
By showing complete solution and explanation determine the slope and deflection at point B of the beam shown by the Area-moment method.
Determine the slope and deflection at point B of the beam shown by the moment-areamethod.
. Use the moment-area method to determine the slopes and deflections at points B and C of the beam shown. A 6m B 3m 250 KN C 3m
The cantilever beam is a 300mm long carbon steel bar, with a diameter of 25mm. And it is charged by a force F = 400 N. A) Find the maximum deflection using the virtual forces method, including that resulting from shear. B) What error will be introduced if the shear is disregarded?
DETERMINE THE HORIZONTAL AND VERTICAL OF THE DEFLECTION AT JOINT B. USING CASTIGLLIANOS THEOREM
Determine the Rotation at C and Maximum Deflection using Double Integration Method