Find out the amount of heat transferred throughan iron fin of length 50 mm, width 100 mm andthickness 5 mm. Assume k = 210 W/mK and h= 12 W/m?K for the material of the fin and thetemperature at the base of the fin as 80°C. Alsodetermine the temperature at tip of the fin, if theatmosphere temperature is 20°C.

Find out the amount of heat transferred through an iron fin of length 50 mm, width 100 mm and thickness 5 mm. Assume k = 210 W/mK and h = 12 W/m2K for the material of the fin and the temperature at the base of the fin as 80°C. Also determine the temperature at tip of the fin, if the atmosphere temperature is 20°C.

Find out the amount of heat transferred through an iron fin of length 50 mm, width 100 mm and thickness 5 mm. Assume k = 210 W/mK and h = 12 W/m2K for the material of the fin and the temperature at the base of the fin as 80°C. Also determine the temperature at tip of the fin, if the atmosphere temperature is 20°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1,155 ft², 4 in. thick concrete wall has inside and outside surface temperatures of 24°C and 4°C. A 2 in. insulation batt with a thermal conductivity of k= 0.03 Btu/(h. ft. °F) is added to the wall. Determine the reduction in heat transfer rate. What is the thickness of the insulation in meters? 0.0508 x Your response differs from the correct answer by more than 10%. Double check your calculations. m What is the thermal conductivity value of the insulation batt in W/(m. K)? 0.05188 W/(mK) What is the R-value of the concrete wall (in m². K/W)? 0.022578 X Your response differs from the correct answer by more than 10%. Double check your calculations. m². K/W What is the R-value of the insulation batt (in m² K/W)? 1.9584 X Your response differs from the correct answer by more than 100%. m² K/W What is the heat transfer rate (in W) when the insulation is added? X W What is the percent reduction in the heat transfer rate? 96 x %
A clearance of 2.8 mm was applied to the laid steel railroad rails that are 11m long,at a temperature of 13°C. At what temperature will the rails just touch each other? Assume α = 11.7 x 10-6/°C and E = 200 GPa
What is the temparature at depth 1 cm from the surface at t=2 minutes after the start of the coolıng ?
Answer this ASAP,thx An empty sphere is made of aluminum (k = 202 W/m. °C) with an inner diameter of 4 cm and an outer diameter of 8 cm. The inside temperature is 100°C and If the ball above is coated with an insulating material having k = 50 mW/m. °C 1 cm thick. The outside of this insulation is in contact with an environment having h = 20 W/m.°C and Ts = 10°C, calculate the heat transfer under these conditions.
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
A semiconductor material has a conductivity of 0.0124 W/cm-K. It has the shape of a rectangular bar with cross sectional area of 1 cm2and length of 3 cm. One end is maintained at 300 °C and the other end at 100 °C. The bar carries a current of 50 A and has resistivity of 1.5x10-3ohm-cm. Assuming the longitudinal surface is insulated, calculated the midpoint temperature in the bar.
A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C, determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10 m/m/°C. Wrong solution will be reported instantly
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
The composite wall which is composed of 10 cm brick (k=0.40 W/m2-C), 2 cm cellotex (k=0.03 W/m2- OC), and 6 cm (k=0.30 W/m2-OC),has an outer (brick) temperature T=23 OC and an inner (plaster)temperature T=90 OC. Find the temperature between the cellotex andplaster in OC.