Filtration Design a granular filtration system for water treatment plant with flow rate of 15,000 m³/day and filter loading rate of 150 m³/m².day. In you design, include, (i) number of filters needed, (ii) filter surface area, (iii) filter dimensions (length, width and depth) and Assume coarse deep mono medium bed with effective particle size 1.3 mm, shape factor = 0.80, porosity = 0.45, specific gravity = 2.65, temperature = 20 °C. Make any other assumption as needed but clearly state and explain your assumption.

Filtration Design a granular filtration system for water treatment plant with flow rate of 15,000 m³/day and filter loading rate of 150 m³/m².day. In you design, include, (i) number of filters needed, (ii) filter surface area, (iii) filter dimensions (length, width and depth) and Assume coarse deep mono medium bed with effective particle size 1.3 mm, shape factor = 0.80, porosity = 0.45, specific gravity = 2.65, temperature = 20 °C. Make any other assumption as needed but clearly state and explain your assumption.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

N 5)( rat ala SIL O 23-A) An activated sludge system is to be used for treatment of 10000 m/day of municipal wastewater. A rimary clarification, the value of BOD, is 150 mg/l, and it is desired to have not more than 5 mg/l. in. ffluent. Assume that Y- 0.5; K, 0.05/day; and ML.VSS-3000 mg/l; Return sludge concentration 10 ng/L. 0 10 days. Determine: Treatment efficiency and the volumetric organic loading. 3) Microorganism ratio 5) The quantity of sludge that must be wasted each day i 2) Reactor volume and detention time. 4) the recycle ratin
A conventional trickling filter is to reduce BOD of wastewater from 250 mg/1 to 100 mg/1. The allowable loading is 20 MLD. The volume required of this filter is off to nearest integer) m³. (round
a) Calculate the organic loading rate of the trickling filter in lb BOD/day/1000 ft3 with the data below. b) What kind of media filter is used in the above question (2a)? Justify your decision. Diameter of TF 60 feet Depth of Media 15 feet Influent Flow 1.5 mgd Influent BOD 150 mg/L
(c) A filter has a head loss of 0.30 m when clean and 1.30 m after 24 hours of filtration at a rate of 1.5l/s. . Estimate the following if the filtration rate is changed to 2 l/s i. head loss immediately after backwash ii. 10 hours later
If (Qr/Q=120 percent of discharge), effluent BOD concentration=80ppm, volume of filter =825m3 , discharge =50L/sec , The influent BOD concentration equal: Choose one: a. 277.89 b. 277.2 c. 276 d. 275
5. A rapid sand filter system is designed for a city with a population is 800,000 and the average water demand is estimated at 350 1/capita-day. The filter design application rate is 120 m/d- m2. i. Design the filter system (number, length and width if L/W is 1.5 and length cannot exceed 12 meters) Calculate the backwash water volume as a percent of total water treated if the backwash time is 12 minutes and rise rate is 0.5 meters/min and backwashing is done once every two days. ii.
Name:.. 11. An activated sludge system has a single aeration basin with a volume of 300,000 gal and 2 - 25 ft. diameter secondary clarifiers. The influent flow is 1.1 MGD, and the influent BODs and TSS are 170 mg/L and 190 mg/L, respectively. The mixed liquor suspended solids concentration is 2500 mg/L, and the recycle suspended solids concentration is 6800 mg/L. The sludge recycle flow rate is 0.60 MGD and the solids residence time is 9 days. 10a. Calculate the volumetric BODs loading rate on the aeration basin in units of lbs/1000 ft³-d. ( 10b. Calculate the F:M ratio in units of g-BODs/g-TSS-d 9
6. The design flow (average daily flow) for a new trickling filter plant for the tri-cities is 52,000 m/d. Raw wastewater characteristics are: 240 mg/L BOD, 240mg/L TSS. Primary settling tank (PST) removes 33% BOD, 70% TSS. The final effluent should have less than 20 mg/L BOD and less than 20 mg/L TSS. Filter depth is 3.2 meters. Determine the diameter of single stage trickling filter(s) using the NRC equation if they are using 3 trickling filters and a recirculation ratio of 3. If we use the BOD loading criteria of 0.6 kg/d-m³ and hydraulic loading rate of 16 m/d-m2 to design the trickling filter will the volume calculated using the NRC equation above be sufficient?
Sanitary Eng. Homework No.5 A WTP is designed to treat 96 X10 m/d. For filtration 16 RSFS are used, each filter is designed with 2 troughs of a square cross sectional area. The filtration rate is 150 m/d. One filter needs 75 m' to be wash for 10 mins FIND 1- Dimensions of each filter, Land W (m). 2- Backwash rate (m/d). 3 -Dimensions of each trough, y and b (m).
3. Determine the diameter of a single-stage plastic media filter to reduce an applied BOD, from 150 mg/L to 50 mg/L. Use a flow rate of 0.20 m/s and a recirculation ratio of 10.0 along with a filter depth of 1.70 m. The water temperature is 20 °C
b) Determine the concentration of the effluent BOD, for the two-stage trickling filter described below The wastewater temperature is 17 C. Assume the NRC equations apply. Design flow = 0.0s09 m/s Influent BODS (after primary treatment) = 260 mg/L Diameter of each filter = 24.0 m Depth of each filter =1.83 m Recirculation flow rate for each filter = 0.0594 m/s %3D
Design a trickling filter system for BOD removal without the nitrification requirement, to treat municipal wastewater with an average flow of 200 m3/d (Qin) and influent BOD of 200 mg/L and Ammonium (NH4-N) of 42 mg/L. Make appropriate assumptions and use the design indicators for plastic media filters as given below. What are the possible effects of the peak flow of 1.5 times occurring once in a month? Volumetric loading rate (Bv)= 0.5 kgBOD/m3.d Volumetric loading rate for NH4-N (Bv, NH4-N)= 0.2 kgNH4-N/m3.d Hydraulic loading rate (qh= Q/AR)= 1.2 m/h Recirculation ratio (Qr/Qin) = 0.5