Fill out the blanks in following statement. The removal of substances from water is accomplished by using biological, chemical, and physical methods. For treatment of potable water sources, chemical and physical techniques are more widely used than biological ones. A water treatment plant uses a combination of several methods, normally operated in series. If the treatment method involves physical forces, it is called a Treatment technologies that are biological or chemical are called

Fill out the blanks in following statement. The removal of substances from water is accomplished by using biological, chemical, and physical methods. For treatment of potable water sources, chemical and physical techniques are more widely used than biological ones. A water treatment plant uses a combination of several methods, normally operated in series. If the treatment method involves physical forces, it is called a Treatment technologies that are biological or chemical are called

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

Calculate the THOD of a 300 mg/L solution of C5H8O2N.
A chemical is added at the beginning of a water treatment plant at a target concentration of 8 mg/L in water. The water treatment plant provides water to a community of 340,000 people and the average water consumption in the city is 130 gallons per capita per day (gpcd). If the chemical is available in a concentrated solution that is 23% (w/w; i.e., 23 lb of chemical/ 100 lb of solution) with a specific gravity (SG) of 1.23, find the quantity of chemical solution that will be required daily (in ft and gallons). It is desired to keep the chemical in 750 gallon tanks and have at least two weeks of chemical storage available. What is the minimum number of tanks that will be required? 4.
EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The concentration of IDS (mg/) in the brine leaving Stage 2 distiller is: Stea Stage 2 Q4 MGD Brine Sea water Q 13 MGD TDS-38000 Frosh water Q11 MGD TDS- 70 mg Heat Heat (ii) 123,308 ad from the giyen information (iv) 246,615 (vi) none of the above (i) 332,615 (ii) 170,615
Explain and relate (as far as you can and to the best of your knowledge) if the turbidity data you get is the initial value of the turbidity of the water, how should the water be treated in the coagulation, flocculation, and precipitation according to the diagram on the side? Primary Secondary Chlorine disinfection tank Bar screen Grit chamber Settling tank Aeration tank Settling tank To river, lake, or ocean Raw sewage Sludge Activated sludge (kills bacteria) from sewers Air pump Sludge digester Disposed of in landfill or ocean or applied to cropland, pasture, or rangeland Sludge drying bed Brooks/Cole, Cengage Learning
Q1.Clearly indicate if each of the following is True or False 1) The amount of bypassed water in split treatment of hardness depends on material balance on Mg². 2) Most water treatment plants in Iraq are using polymers as a coagulant. 3) In drinking water, most of alkalinity comes from SO4². 4) Circle or ring system is the most common method used now to design water distribution systems. 5) Fecal Coliforms and E-Coli are generally pathogenic and we need to test them to avoid their diseases. 6) In flocculation process, we need rapid mixing to enhance formation of flocs for better settlement. 7) In filtration, the only mechanism involved is the straining. 8) It is better to travel downhill, avoid rush hours, and avoid left turn when designing a route for packers. 9) Ozone in Stratosphere layer helps prevent UV light from reaching earth and causing skin problems. 10) Transfer station is used to transfer solid waste to final destination in more efficient way.
A liquid delivery system is being designed such that ethylene glycol flows out of a hole in the bottom of a large tank. The designers need to predict how long it will take for the ethylene glycol to completely drain. Since it would be very expensive to run tests with a full-scale prototype using ethylene glycol, they decide to build a one-quarter scale model for experimental testing, and they plan to use water as their test liquid. The model is geometrically similar to the prototype as shown in the Figure.(a) Temperature of the ethylene glycol in the prototype tank is 60°C, at which υ = 4.75x10-6 m2/s. At what temperature should the water in the model experiment be set in order to ensure complete similarity between model and prototype?(b) The experiment is run with water at the proper temperature as calculated in part (a). It takes 3.27 min to drain the model tank. Predict how long it will take to drain the ethylene glycol from the prototype tank.
10-Pumps that lift surface water and move it to a nearby treatment plant are called: B- Rotary pumps High lift pumps C- Low lift pumps D- Reciprocating pum A-
Computation: Ratio Strength, PPM, mg%Show your complete solution.1. If a city water supply has a limit of 250 ppm of nitrate ion, what is the maximum amount of nitrate ion in grams that may be present in a 10,000 gallon reservoir?Amount of nitrate ion in grams = ?
A water source has a flow of 10 MGD, alkalinity of 275 mg/L in CaCO3, and a pH of 8.85. What will the alkalinity be after addition of 150 mg/L NaOH? Present your answer in mg/L as CaCO3. Assume a close system.
A container contains 200 g of solution in which 30 grams of salt are dissolved. Brine containing 1 g of salt/L is then poured into the tank at the rate of 4L / m * i * n and the solution is mixed well and is pumped out of the same rateFind the amount of salt in the container after 5 minutes ?
The amount of chlorine residual remaining when gases start evolving during disinfection and when they stop evolving, respectively, are: A B с D Chlorine residual (mg/1) 0.9 0.6 D 1.2 16 1.2 mg/1 and 1.6 mg/1 1.6 mg/1 and 1.2 mg/1 1.6 mg/1 and 1.2 mg/1 0.9 mg/1 and 0.6 mg/1 Chlorine added (mg/1)
What is turbidity, what causes it, how is it treated why it is undesirable in drinking water. Describe processes in water treatment? Calculate the velocity gradient in a rapid mixer (coagulation), where the power input to the propeller is 0.5 kW, the plant provides water for 13000 people with average consumption of 130 L/person/day, retention time in rapid mixer is 23 s and water temperature is 20 oC. The dynamic viscosity at 20oC is 1x10-3 Pa/s. Debate the G value and if out of the range what steps to take bring G in the correct range