Figure In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by pin at A and a rof at B. Determine the diameter of the pin at A it is double shear. 1. A = 900 mm? L= 3 m. cable E = 70 GPa 2 m. 3 m. Double shear 2. In Problem 1, determine the vertical dis- placements at. B abd C as required by the load 20 kN. A В C 600

Figure In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by pin at A and a rof at B. Determine the diameter of the pin at A it is double shear. 1. A = 900 mm? L= 3 m. cable E = 70 GPa 2 m. 3 m. Double shear 2. In Problem 1, determine the vertical dis- placements at. B abd C as required by the load 20 kN. A В C 600

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

4.00kips Ib 600- ft Problem 3. Pin B acts in double shear and has diameter d=3/4 in. Pins are fabricated using a material for which Tailure = 12000 psi. A, B 3 ft < 3 ft 6 ft Determine the Following: a. Reaction at A (magnitude and direction): b. Reaction at B (magnitude and direction): c. Average Shear Stress Pin B: T, d. Factor of Safety of Pin B: F.S. =
A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa 25° A B Wheel
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
Solve Problem for the maximum shear stress within regions AC and BC, and the angle of twist f of end B relative to C.
Figure A = 900 mm? -cable L= 3 m. E= 70 GPa 3 m. 2 m. 2. In Problem 1, determine the vertical dis- placements at. Babd C as required by the load 20 kN. Double shear A B 60° P = 20 kN
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)
The rigid bars shown are separated by a roller at Cand pinned at A and D. A steel rod at B helps support the load of P 55 kN. Compute the vertical displacement of the roller at C. Given: a - 2 m, b 3 m, C= 3 m, d 1.9 m. E - 203 GPa, A 337 mm and L-2 m. Answer must be in mm.
G2/ The bar AB is considered to be absolutely rigid and is horizontal before the load of &8000 N is applied. The conneetion at C is a pin, and AB is supported by the bronze rod EA and the steel rod FB. The length of EA is 4m and FB is 3 m. Neglect any possibility of lateral buckling and the weights of all bars „Calculate the stresses in each rod. For bronze E=100 GPa, A=50 mm? for steel E=200 GPa, A=30 mm2 Steel L=3m 10m 5m Bronze L=4m 8000 N
G2/ The bar AB is considered to be absolutely rigid and is horizontal before the load of &8000 N is applied. The conneetion at C is a pin, and AB is supported by the bronze rod EA and the steel rod FB. The length of EA is 4m and FB is 3 m. Neglect any possibility of lateral buckling and the weights of all bars „Calculate the stresses in each rod. For bronze E=100 GPa, A=50 mm2 for steel E=200 GPa, A=30 mm2 Steel L=3m 10m 5m Bronze L=4m 8000 N
The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the plates is 30 ksi, allowable shearing stress is 24 ksi for the rivets and 28 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploratory sections. Your solutions are invalidated without the required FBDs.
Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 18 in P 0.5 in. 18 in. C Determine the average bearing stress at Bin member BC The average bearing stress at B in member BC is ksi.
A hydraulic press exerts a total load of 5.5 MN. This load is carried by two steel rodssupporting the upper head of the press. If the safe stress is 95 MPa and Young Modulus of209 KN/mm?. Find; (i) Diameter of the rods (ii) Extension in each rod in a length 3.5 m