Figure 3 for #11 to #12.LM 117VOUTVOUT R2 is half as much as R1VIN-28VVINand Vref is 2V.ADJR1240Vrefladj11C2C1** 0.1µFR2 Electronic circuitsPlease determine the following:11. What is the adjusted valueof the current in Figure 3 withthe given variables?O 150mAO 75mAO 50mAO 2mA12. What is the adjusted valueof R2 with the same givenvariables and adjusted currentof #11 if the output voltage is9V?0 84 ohmsO 48 ohmsO 48 kilo ohmsO 550 ohms

We need to find current and resistor for given circuit

Answered: Figure 3 for #11 to #12. LM 117 VIN-28V…

Figure 3 for #11 to #12. LM 117 VIN-28V VIN VOUT VOUUT R2 is half as much as R1 and Vref is 2V. ADJ R1 240 Vref ladj 11 C2 0.1uF R2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 4. We want a peak load voltage of 40 V out ofa bridge rectifier. What is the approximate rms value…

A: As per the guidelines of bartleby, we have to solve first 3 questions among the multiple subpart…

Q: Calculate Io

A: In this question, We need to determine the current Io as shown in the circuit. We are solving this…

Q: 7. If line frequency is 60 Hz, what is the output frequency of a bridge rectifier? 8. If the load…

A: As per the guidelines given to us, we can only provide the solution of first question in multiple…

Q: 1. Looking at the transmitter, the signal power is 23 mW. The input signal to noise ratio is 40 dB.…

Q: IBQ, ICQ, VE, VCEQ, VCfor a transistor with VBE= 0.6 and β = 50. Draw and label the DC load-line.…

A: We need to find out current and voltage for given circuit

Q: Discuss with block diagram, the principle of operation of single phase energy met

A: (i provide you the solution in RULE PAPER for easily understand to the diagram and its related…

Q: Figure 1 for #1 to #5. V1 3:2 A1 V2 ww 1K A2 AC voltage Source A3 АЗ 220V D2

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 5.00 иF 3.00 иF 4.00 µF 2.00 µF 3.00 µF 6.00 μF 7.00 иF 48.0 V

Q: In the circuit above:, the supply provides 3 V, the resistor is 1.66 kN, and the inductor is 13 mH.…

A: The solution is given below The given problem is from series RLC circuit.

Q: Ro Cc loka Ce RL 2K Av nd = -3 CG - 0-01 MF C9s- 30 PF Find Au felMHZ

A: We need to find out gain at given frequency

Q: How many calories are developed in 1.0 min in an electric heater which draws 5.0 A when connected to…

A: In this question, We need to choose the correct option What is energy in calories if Voltage V=…

Q: 1. What is the measured value of V1? 2. What is the measured value of V2? 73.33V 73.33V O 103.71V…

A: According to the question, for the given circuit as shown below We need to find V1, V2, and A1

Q: The open-loop gain of a certain op-amp is 175,000. Its common-mode gain is * .0.18. Determine the…

A: The CMRR is given by the ratio of open loop gain and common mode gain. Here we have open loop gain =…

Q: Determine i in the circuit. 30 N 12Ω 5Ω 20 Ω 12V 25 Ω 60 2 15Ω 10 2

A: The solution is given below

Q: Vec Rc RB VE OE For the circuit shown above, assume Vcc- 12V, Ra 330KO, Rc- 1.5kO,B- 120. Determine…

Q: Determine the Thevenin's and Norton's uivalent circuits at terminals a-b. 12V ミuう (2V びり: 12V + (+)

Q: 4. Two identical magnetically coupled coils have an equivalent inductance of 80 mH when connected in…

A: The solution is given below

Q: DI 3:2 A2 AC voltage Source 1K A3 220V D2 (s)

Q: 1a) Please detail the importance of Analog and Digital Electronics. Write several applications and…

A: Efficiency and regulation are important concepts in dealing electrical machines. Different…

Q: Vcc = 20 V Required: a. IBQ, Ica, VE, VCEQ, Vc for a transistor with VBE = 0.6 and B = 50. %3D b.…

A: We will draw dc load line and we will find out current and voltage .

Q: 1mH vz(t)

A: Given circuit shown

Q: Find the Laplace transform

Q: 5 minutes 3. The reactance offered by a capacitor to alternating current of frequency 50 Hz is 10…

Q: = 15 V, V = 6 V termine the minimum voltage. -11 V -15 V -21 V 0-9V

Q: An auto transformer design for 4000/2300 Volt operation supplies a load of 32 kw at a power factor…

Q: 4) Express 35dBm in terms of (a) dB and (b) dBV

Q: Sketch the final waveform of below circuit. V1 D2 9V R1 25V

A: In the given circuit, a battery is connected negative or reverse bias to the diode and a resistance…

Q: Identify the electrical symbol.

Q: Q1. A series Op-Amp voltage regulator which its input voltage is 15V and to regulate output voltage…

A: Operational Amplifier: Operational amplifiers are linear devices with all of the qualities necessary…

Q: Determine V, and I, for the networks below. 15V Ip Si D1 Si D2 +V, 2.2kn -5V

A: The solution is given below Basic diode problem.

Q: In a signal phase, pedestrians are allowed to cross the street walking in the same direction as…

A: It is given that: Crosswalk length=L=722 ft=36 ftWE=9 ftWE<10 ftδp=4 ft/secNpld=20

Q: Utilice el análisis de mallas en el circuito de la figura 8-80 para encontrar la corriente I1. R3 =…

A: To calculate the current I1 by using mesh analysis. First consider current source and convert it to…

Q: A: Under same conditions (all the variables are equal) of air density factor ( 8), irregularity…

A: In this question we need to prove mathematically that visual critical voltage is greater than…

Q: A current transformer with bar primary has 300 turns in its secondary winding. The resistance and…

A: A bar type current transformer utilizes the real cable or bus-bar of the main transformer as the…

Q: Q2: A three-phase Transmission line with 1,956 cm diameter conductor, the corona takes place if the…

Q: A DC machine running at 750 rpm has an induced emf of 200 V. Calculate (1) the speed at which the…

Q: 9. The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. What is the…

A: For both the questions we are given rectifier type as bridge rectifier A bridge rectifier contains…

Q: f(t) A A T -T -A Determine the Fourier series of the function in Fig. 16.12(a). Take A = 1 and T =…

A: Trigonometric Fourier series :

Q: You have two fixed bias circuits connected for testing. They are identical except that one is biased…

A: Biasing: Biasing is the process of determining an active component's initial operating…

Q: A rectangular flat surface with sides 0.200 m and 0.500 m is under the influence of a uniform…

A: It is given that: Length of sheet=L=0.2 mWidth of sheet=b=0.5 mUniform Electric field=E=85 N/CThe…

Q: What is the phase relationship between the voltage and current in an AC resistive circuit?

A: We need to find out phase relationship for resistive network .

Q: Rf Vo is (t Rs RL

Q: Use nodal method to find the branch currents I1, I2, I3, I4 and I5 in the network.

A: The given circuit is as below,

Q: given the expression below Reqd 1.) grouped k-map in POS 2.) minimum POS expression

Q: Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent…

A: Truth table: It is a tabular representation of the output and the inputs of the gates. With the help…

Q: Determine Vo and I, for the networks below. 15V Ip Si AD1 Si D2 +V, 2.2k. -5V

Q: sing Given that D = 2pcosp a, az, in cylindrical coordinates, find the flux crossing 2p %3D the…

A: We need to find out flux crossing the given surface

Q: a capacitor for a capacitor-start copacitor-run motor is connected in _____ with the windings to…

A: The solution is given below

Q: An open–wire transmission line is made from two wires, each with a diameter of 2.5 mm, located 16 mm…

A: In this question we will write effect on characteristic impedance of open wire transmission line if…

Q: superposition theorem.

Question

100%

Figure 3 for #11 to #12.
LM 117
VOUT
VOUT R2 is half as much as R1
VIN-28V
VIN
and Vref is 2V.
ADJ
R1
240
Vref
ladj
11
C2
C1*
* 0.1µF
R2

Electronic circuits
Please determine the following:
11. What is the adjusted value
of the current in Figure 3 with
the given variables?
O 150mA
O 75mA
O 50mA
O 2mA
12. What is the adjusted value
of R2 with the same given
variables and adjusted current
of #11 if the output voltage is
9V?
0 84 ohms
O 48 ohms
O 48 kilo ohms
O 550 ohms

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1,

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

R1 Vi 1kO Di IN4148 D2–1N4148 5V Vo -5V -3V Figure 1 a)Draw a simplified circuit for positive and negative cycle then calculate the output voltage (Vo) for both cycles. b)Sketch the output waveform, Vo for the circuit.
For self bias configuration. Solve for Ib and Ic. ... 4 RC 15002 RB VCC 5 16V 100A/A 80 kQ Re 10002 Ib=Blank 1 HA Ic=Blank 2mA
An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin. Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
M EXPERIMENT 01 V(n002) V(n001) 10V- 8V- 6V- 4V- 2V- OV- -2V- 4V- -6V- -8V- -10V- 0.00ms 30.00ms 60.00ms 90.00ms 120.00ms 150.00ms 180.00ms K EXPERIMENT 01 X Diode 1N914 V Resistor SINE(0 10 60000 100) 10K .tran 2
The diodes in the circuit in Figure Q7 have V = 0.7. Determine the output voltage Vo and the currents Ip1, ID2, D3, and I for the following input conditions: V₁ = 2V V₂ = 3V *** In which all the diodes are ON state Parameter Valuc 101 = 6.05 A D2 = 665 9.05 N 9.65A 03 Vo = 5.725 1 - 10 - 19.50 -0.7 - 5 = 0.45m²ß U. = 10 19. H - (.45mA x 9.5 KR) = 5.725 W : 5.75 -02:22 0.5. k IN S. 725-0-7-7 6.05 m/ 3 4.0% XIU A 27 2 3 Vo 05 kQ 0.5 k 120 www IDI 1pz D₁ D₂ Figure Q7 +10 V lost [ f +5 V 9.5 KQ D ovo 77°F Clear
Post-lab Questions If the diode D3 is damaged (as short) draw the output voltage waveform in this case. D1 D2 V1 F1 220Vrms n 50HZ T1 0° 220v:40v D3 D4 transformer
Solve the approximate value of Ic of Figure 45. Vcc T16V R1 33.9ka 68kN Vc Q1 Beta = 85 - VE R2 9.1ka S0.72KΩ
Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Thyristor Crout Probe Pulse Generator VC, pulses Probe Scope Thy Orso v Joad O R: 1 The output voltage across R is depicted in 0.5 0.0- b) 0.2 0.0 d)
Isolator MCB MCCB RCD BIE Noark D 20A 480Y/277V 50/60Hz 5000A E355391 CAUS us D-OFF C D-OFF The shown protection device is
PROBLEM: The diode (blue line) should be at -10V not -8V SOFTWARE USED: LTspice XVII---Figure 1 is my work, and figure 2 is the correct sample. Please tell me what I did wrong. Thank you :))---Below is the .asc filehttps://www.mediafire.com/file/zxauoh86zi79nfu/EXPERIMENT_01.asc/file
this is electric circuit questin ...plz solve it early .plz solve early