Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2

Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter13: Slope Stability

Section: Chapter Questions

Problem 13.29CTP

See similar textbooks

Related questions

Q: An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m…

A: (a) It is required to determine the factor of safety of the slope. Here, c’ is the cohesion, H is…

Q: A cut slope was excavated in a saturated clay. The slope made an angle of 39.55 degree with the…

A: a) The expression for the depth function when the slope angle is less than 39.55 degrees is given as…

Q: A cut slope is to be made in a clayey soil to permit construction of a new highway as shown below. A…

A: The factor of safety against sliding: Fs=C+σn¯tanϕτ .......................................(1)…

Q: 15.10 The inclination of a finite slope is 1 vertical to 2 horizontal. Determine the slope height,…

Q: A long slope is made with sand having an internal friction angle of 36°. If the slope is submerged…

A: Given data: Internal friction angle of sand, ϕ = 36° Factor of safety = 2 Saturated unit weight of…

Q: Compute the force that causes sliding. Compute the resistance sliding force. Compute the factor of…

Q: 3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17…

A: The given data is shown below: c=30 kPaφ=30°γ=17 kN/m3

Q: A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of…

A: given data: A cut slope was excavated in saturated clays as shown in the figure. The soil has a…

Q: 3. A cut slope consist of soil materials that has a unit weight of 16 KN/cu.m and undrained shear…

A: Unit wt of soil (γ)=16 KN/m3Undrained shear strength(cu) =28KN/m2β=50°stability number(Sn) = 0.17

Q: Q.3. A cut slope was excavated in a saturated clay with a slope angle β = 57 ͦ with the horizontal.…

A: Given Data;Slope Angle = β=57°Deptj of cut =H =8mDepth of rock layer fro the surface is Dh = 2mUnit…

Q: A 25-m high rock cut with a face angle of 60° has been excavated in a massive, very weak volcanic…

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are…

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: An unsupported slope of height 15 m is shown in the figure (not to scale), in which the slope face…

A: Cohesion is mobilised along the curve . Weight of solid mass give overturning moment along the…

Q: An infinite soil slope with an inclination of 35° is subjected to seepage parallel to its surface.…

Q: If an infinite slope of clay at a depth of 6 m has cohesion of 60 kN/m2 and unit weight as 18 kN/m3,…

A: Given data, for an infinite slope of clay at a depth of 6 m has cohesion of 60 kN/m unit…

Q: 15.6 A slope is shown in Figure 15.50. If AC represents a trial failure plane, determine the factor…

A: To determine the Factor of Safety-

Q: Find the factor of safety against sliding assuming there is no water pressure.

Q: 13 Using the graph shown in Figure 15.13, determine the height of a slope (I vertical to 2…

Q: An infinite slope of soil, with height 10 m, is inclined at an angle of 35° to the horizontal. The…

A: Given- Height=10 mangle of inclination=35oCohesion C'=22 kN/m2ϕ'=22oIt is needed to find the FOS

Q: An infinite slope in purely cohesive soil has a saturated unit weight of 20 kN/m^3 and effective…

Q: factor of safety against sliding, factor of safety against overturning,

Q: 5.15 A cut slope was excavated in a saturated clay with a slope angle, B = 48; with the horizontal.…

Q: For the infinite slope shown in Figure 15.46, determine the height, H, for critical equilibrium.…

A: The formula to calculate the height for critical equilibrium is given by, H=c'γ×1cos2βtanβ-tanϕ'…

Q: 3. For the slope shown in Figure below, determine the factor of safety against sliding along the…

Q: An unsupported slope of height 15 m is shown in the figure (not to scale), in which the slope face…

Q: For a railway track 7 m high embankment is required. The clay to be used for the embankment was…

Q: 3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety…

A: Given values, H =22 m slope of inclination, i= 39° inclination of failure plane, θ= 28° cohesion, c=…

Q: 15.21 Determine the minimum factor of safety of a slope with the following parameters H = 14 m, ß =…

A: Height(H)=14 m, Unit weight(γ)=19 kN/m3, The angle of internal frictionϕ'=25°, Cohesion(C)=20 kN/m2,…

Q: 3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety…

Q: A very long slope is inclined at an angle ßto the horizontal, in a clay soil having a unit weight y=…

Q: If an infinite slope of clay at a depth of 6 m has cohesion of 3 t/m² and unit weight of 2.5 t/m3,…

A: given- depth H=6 m cohesion C=3 t/m2 unit weight γ=2.5 t/m3

Q: 15.1 Refer to the infinite slope shown in Figure 15.47. Given: B = 25°, y= 17.8 KN/m', d' = 28", and…

Q: The soil of a infinitely long slope has cohesion of value 20 kPa and dry unit weight of 16 kN/m3. If…

Q: 15.24 The following parameters are given for a slope with steady-state seepage: Slope angle: 3H:1V,…

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane…

A: Given Data: β=58°θ=32°H=6mγ=19kN/m3ϕ=21°c'=38kN/m2 The factor safety is ratio of the resisting…

Q: Q1 The rock slope has been mapped and analysed. The data of slope geometry and rock parameters…

Q: Consider a slope given below with 10 slices, which has a circular failure surface. Each slice has 5…

Q: The figure below shows a slope with an inclination of B = 56°. if AC represents a trial failure…

Q: A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of…

A: Given; stability number m = 0.185. undrained shear strength cᵤ = 20 kPa soil has a unit weight =17…

Q: Refer to Figure 15.50. Given that β = 55°, γ = 19 kN/m3, ϕ′ = 17°, c′ = 57.4 kN/m2, and H = 13.7 m,…

A: failure of plane due to sliding are failure of infinite slope. under sliding condition ,for cohesive…

Q: A trench was cut in a clay slope as shown in the figure. When the trench reached a depth of 3 m, the…

Q: An unsupported slope of height 15 m is shown in the figure (not to scale), in which the slope face…

A: Given data- Radius R=25 mAngle θ=60oCohesion C=75 kPaWeight W=2500 kN/mhorizontal distance x=10 m…

Q: The following parameters are given for a slope with steady-state seepage: Slope angle: 3H:1V, ø' =…

A: As u have asked for answering part (a) only solving thatSlope angle : 3H:1V ϕ'=24°c'=27 Knm2γ=17.5…

Q: 3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety…

A: Factor of safety = shear strength shear force = τs Normal component of wedge ABC N = w cos ϕ where,…

Q: A 40° slope is excavated to a depth of 10 m is a deep layer of saturated clay of unit weight 20…

A: Given data: depth(H)=10m slope=40o unit weight of saturated clay=20 kN/m3 Shear strength parameter…

Q: A 10 m high slope of dry clay sol (unil weight = 20 N/m) with a slope angle of 45 and the circular…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 30° slope has a height of 10 m as shown in the figure below. The soil in the slope has the following parameters c = 20 kPa, ϕ = 0°, γ = 18 kN/m . Calculate the factor of safety for the slip surface shown in the figure.
Sand is placed on a rock slope, as shown in Figure Q2. (a) Show that sand will be stable (i.e., no sliding sliding) if
3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety against plane failure assuming: p (degree) > (kN/m³) c (kPa) 55 2800 1850 c: cohesion of rock mass; y: unit weight of rock mass; p: friction angle of rock mass جیهان کاظی
Q.4 A 40° slope is excavated to a depth of 8 m in a deep layer of saturated clay having strength parameters c = 60 kN/m2 , Ø = 0, and ɣ = 19 kN/m3 . Determine the factor of safety for the trial failure surface shown in Fig. 4
Figure below gives details of an embankment to be made of cohesive soil with c, = 20 kPa. Unit weight of soil is 19 kN/m³. For the trial circle shown, determine the factor of safety against failure. The weight of the sliding sector is 329 kN acting at an eccentricity of 4.8 m from the centre of rotation. What would be the factor of safety if the shaded portion of the embankment were removed? Assume no tension crack develops. 71° R = 9 m e = 4.8 m 3 m 1.5 m 1.1 3 m VINIS
3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety against plane failure assuming: 9 (degree) 7 (kN/m³) c (kPa) 4) 50 2600 1950 c: cohesion of rock mass; y: unit weight of rock mass; q: friction angle of rock mass 1 1
(Note:Depth of rock layer is 2m not 12 m.) Q A cut slope was excavated in a saturated clay with a slope angle β = 57 ͦ with the horizontal. Slope failure occurred when the cut reached a depth of 8 m. Previous soil explorations showed that a rock layer was located at a depth of 2 m below the ground surface. Assuming an undrained condition and that ɣsat = 21 kN/m3 : Determine the undrained cohesion of the clay (Fig 3). What was the nature of the critical circle? With reference to the top of the slope, at what distance did the surface of the sliding intersect the bottom of the excavation?
A cut slope was excavated in a saturated clay. The slope made an angle of 39.55 degree with the horizontal. Slope failure occurred when the cut reached a depth of 6 m. Previous soil explorations showed that a rock layer was located at a depth of 10 m below the ground surface. Assuming an undrained condition and γsat = 18 kN/m3, Analyze the following. a. undrained cohesion of the clay.b. nature of the critical circle?c. With reference to the toe of the slope, at what distance did the surface of sliding intersect the bottom of the excavation?
A 40° slope is excavated to a depth of 8 m in a deep layer of saturated clay having strength parameters, c = 60 kN/m², p = 0, and y- 19 kN/m³. Determine the factor of safety for the trial failure surface shown in below figure using Swedish circle method. 8 m 40° 95⁰ R = 10.2 m 4m- W = 1050 kN THE W
Q1. For the slope shown in the figure, determine P (kN/m) so that the factor of safety for the given failure surface in terms of total 7.25 m P(kN/m) 1,5 28* stress (short term stability) is 2. The unit weight for both soils is 17 kN/m'. For soil 1, the relevant shear strength parameters c, = 30kPa, o=0°, and for soil 2, c, 55 kPa, @=0°. .72 4.0 Soill are Area -2.0--1.9- 41.7 m 3.0 Soil 2
Q.4 A 40° slope is excavated to a depth of 8 m in a deep layer of saturated clay having strength parameters c = 58 kN/m², Ø = 0, and y = 18 kN/m³. Determine the factor of safety for the trial failure surface shown in Fig. 4 Q.5 Figure 5 shows an infinite slope with H = 32 ft and the groundwater table coinciding
A level site underlain by fully saturated clays is cut over a few days as shown in the figure below. The water table is located at the ground surface across the site. Determine the resisting moment in kN.m for the circular slip surface depicted in the Figure below shortly after excavation. Consider the soil wedge above the circular slip surface as a single free body, whose plane area is equal to 100 m2 and the centre of gravity of the soil wedge is given at Point C.