Figure 2 Question 3 The combined pulleys in Figure 3 use friction to transmit motion. If block A has a linear displacement of 0.2 m downward, determine: I. the angular displacement of pulleys B, C and D, and II. the linear displacement of E. Ø 0.24 m Ø 0.3 m Ø 200 mm Ø 120 mm Ø 0.1 m B A 2 80 mm Figure 3

Figure 2 Question 3 The combined pulleys in Figure 3 use friction to transmit motion. If block A has a linear displacement of 0.2 m downward, determine: I. the angular displacement of pulleys B, C and D, and II. the linear displacement of E. Ø 0.24 m Ø 0.3 m Ø 200 mm Ø 120 mm Ø 0.1 m B A 2 80 mm Figure 3

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

Q/ Crank, AB = 200 mm; Slotted arm, OC = 800 mm and link CD = 250 mm. B=30 °. find the velocity of D when the linear velocity of sliding is 1.7 m/sec ww 008 400 mm
QUESTION 7 Consider a pulley system shown below. The coordinate x is the displacement of G. Assume there is no slip between the cord and the pulley, and disk and the ground. k ooood L Find the equation of motion. There is only one answer. m2 (---) + + 2 m₁+m₂+ 1 I\d²x 2 R² dt² (=/m₂ + ²₁ +m ²₂+ m 2 m₂, I, R +-+ m₁+ 4 I d²x +kx=m₁₂8 I \d²x R² dt² +4kx=m₁₂8 Id²x R² d1² +4kx= 2 0 (2m, + m₂ + 2) + I d²x R2 d₁² d²x I 0 (m₂ + 4m² + 2)² + 4x: dt² |m₁| +2kx=2m₂8 +4kx==m₁8 +4kx=m₁8
The crank-rocker mechanism shown has lengths n = 9 in, r2 = 2 in, r3 = 7 in, andr4= 10 in. Find the angular displacement Aa that crank OA makes to move the rocker OpB from the extreme right to the extreme left position. Crank OAA rotates counterclockwise as shown. Write your answer in degrees but do not write the units. B A 0B Answer. DELL
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Analytically determine the linear displacement of the piston in the compressor linkage shown in the figure as the 45 mm. crank is rotated from its current position 90 degree clockwise.
Q1. In a link work, as shown in Fig. below, the crank A B rotates about A at a uniform speed of 150 r.p.m. The lever DC oscillates about the fixed point D, being connected to A B by the connecting link BC. The block F moves, in horizontal guides being driven by the link EF, when the crank A B is at 30°. The dimensions of the various links are: AB = 150 mm; BC = 450 mm; CE = 300 mm; DE = 150 mm; and EF = 350 mm. Find, for the given configuration, find 1- angular acceleration of link DC, and 2- acceleration of slider F. 75 mm www 450 mm 37,5 mm A
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
Pulleys 1 and 2 of the rope and pulley system are connected and rotate as a unit. The radii of pulleys 1 and 2 are 100 mm and 300 mm respectively. Rope A is wrapped around pulley 1 and is fastened to pulley 1 at A’. Rope B is wrapped around pulley 2 and is fastened to pulley 2 at B'. Rope C is continuous over pulleys 3 and 4. Each rope as a diameter of 15 mm. Determine the normal stress in each segment of rope C if the weight has a mass of 225 kg. B'A' B T W
4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
The length of the links are known for the mechanism shown in Figure. The angle of driver link 1 with the horizontal is ϕ= ϕ1 and the angular speed of driver link 1 is n = n1. The input data for ten cases are given in the table in Figure. Determine:a) the number of DOF of the mechanism.b) the positions of joints B, C, D, and E for a complete rotation of driver link 1,ϕ=[330°].c) the linear velocities of joints B, C, D, E and the angular velocities of links 2,3, and 4 for a complete rotation of driver link 1, ϕ=[ 330°].d) the linear accelerations of joints B, C, D, E, and the angular accelerations of links 2,3, and 4 for a complete rotation of driver link 1, ϕ=[ 330°].