FIG. 3.8 0.75 0.5 0.25 Dj. VR (volts) 0 4. Draw the waveform for the voltage across the resistor in a R-L circuit on the graph shown below (Fig. 3.8). Use a 1.0 V (p-p) square wave for the input voltage at a frequency of 80 Hz and let R= 1.0 k and L = 1.0 H. Also, draw the input waveform. Calculate the volt- age for at least ten data points from 0 to 6.25 ms. Show T, 27, 37, 47 and 57 on the graph. Neglect the resistance of the inductor. What is the value of T? 1.0 R₂ 1 2 T 3 4 5 6 7 8 9 10 t(ms)

FIG. 3.8 0.75 0.5 0.25 Dj. VR (volts) 0 4. Draw the waveform for the voltage across the resistor in a R-L circuit on the graph shown below (Fig. 3.8). Use a 1.0 V (p-p) square wave for the input voltage at a frequency of 80 Hz and let R= 1.0 k and L = 1.0 H. Also, draw the input waveform. Calculate the volt- age for at least ten data points from 0 to 6.25 ms. Show T, 27, 37, 47 and 57 on the graph. Neglect the resistance of the inductor. What is the value of T? 1.0 R₂ 1 2 T 3 4 5 6 7 8 9 10 t(ms)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

this is electric circuit questin ...plz solve it early .plz solve early
Find voltage v₁ of the circuit in the Figure, where D is an ideal diode. Rs US + I R₁ VD D RL VL
Q3: The output for the following clipping circuit is shown below. Assuming ideal diode, calculate g the average value and the RMS value for the output of the circuit. V Vin Vm Vin RL V - Vm (a) - (Vm+ V) V
ECETopic: Thyristor3. What is the difference between 2N6505 and 2N6508 SCR?
Q1/ Sketch the output waveform for the circuit. 15V V. RL Vo -15V Va 7V Input waveform ww.
Shown in the figure is a schematic of a power electronics circuit. a) Identify the power semiconductor devices included in the circuit b) sketch their symbol with terminal identification c) explain the function of power semiconductor devices included in the circuit 120kn 240 V 60 Hz 2N2574 ODeg 1.0kn ECG6412 :100nF
Given: Si Diode + R 16 Vi Vo + 4 V -16 Determine Vo for the network and sketch the output waveform
Q3 (a) Figure Q3(a) shows the circuit diagram diode as a clamper. (i) Name the type of clamper. Determine the overall output voltage, Vout) of the circuit. Show all the calculations and support your answer with the aid of diagram. (iii) Sketch and label clearly the output voltage in parallel with the input voltage. The input voltage is shown in Figure Q3(b). +с - + Si Vin R = 1kn VOUT Voc= 7V Figure Q3(a) Vin 10 - 10 Figure Q3(b)
What is the output waveform of the circuit? TP1 ΤP2 220V 1k Ohm Select one: d. e. None of the choices
1. A diode is hooked up to an IV analyzer as shown and the analyzer produces the graph below. Based on the diode symbol this type of diode is a/an: a) LED b) Silicon c) Germanium d) Zener XIVI IV analyzer-XIV1 IV analyzer-XIV1 12m 9m 6m 3m D1 Om 1N4730A -3m -6m -9m -12m -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 Voltage (V) (V_pn) Current (A) (I_p)
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.55 V respectively. The form factor of this circuit is a. 3.67 b. 0.55 c. 1.35 d. 1.83
use the constant voltage drop model in analyzing the diode circuit below: 10 92 V₁ (+ M 1 V D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF C B. D₁ is OFF and D₂ is ON - 1 V D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON + 1092 Vo