F8-11. Determine the vertical displacement of joint C. AE is constant. Use the principle of virtual work.

Q: A-2 Determine the vertical displacement of joint C.Assume e members are pin connected at their end…

A: A = 200 mm²   E = 200 Gpa

Q: pitch, the torque required for achieving the tightening force is

A: Given data; tightening force=2200 N Pitch=0.004 m

Q: 4-35 Deter mine compressive logds in members AB and BC. FBD of B BC AB=160 AB/I5 160lb AB = 3401bin…

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 630 N, a =…

A:

Q: The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive.…

A: Given data: Diameter d1 = 0.3 m Diameter d2 = 0.2 m Centre distance, x = 1 m 2β = 60° Speed, N = 400…

Q: This is a question of one of the practice problems for this topic. After obtaining the forces in…

A:

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A:

Q: 3. Determine the displacement (n) of the whole spring system given if the net force applied to the…

A:

Q: Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the…

A: Given Data

Q: PI0-4. The motor delivers 10 hp to the shaft. If it rotates at 1200 rpm, detemine the torque…

A: Given data

Q: 12% of the load (3695 N) to be transferred, determine if pre-compression (a.k.a. pre-load) should be…

A:

Q: A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be…

A: Here is the solution for the above question.

Q: The bridge construction company Z is facing problems with the mechanism of the crane, which it uses…

A:

Q: when the beam is horizontal. For W-90 lb and the stiffness of the spring k-313 lb/in, determine the…

A: The free-body diagram is-

Q: A block placed under the head of the claw hammer as shown greatly facilitates the extraction of the…

A: According to the given dataPulling load =60 lbWe need to findReaction at A

Q: ghtening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque requi

A: given:tightening force =2200NPitch=4mm

Q: Determine the reaction forces at pins A, B and Cusing method of parts (frames). Show all work…

A: Consider the free body diagram shown below for the BC.

Q: Draw free-body diagrams of members AC and BG 3 m -8 m G 2 m 15 2 m 8 2 m A 300 N 3**3**3*

A:

Q: Determine the forces at all joints 3 in G 1000 Ib B 10 in 5 in 5in

A: Taking vertical and horizontal reaction at A , Va and Ha Taking vertical and horizontal reaction at…

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

A:

Q: Block A wieght lo k and blocK B wieghnt 20 RN, the coeficient of Priction between Block A and Bis…

A: given: weight of A=10KNWeight of the block B=20KNCoefficient of friction between A and…

Q: 4/24 Verify the fact that each of the trusses contains one or more elements of redundancy and…

A:

Q: find the forces in all joints

A: Consider the free body diagram of the pulley. From the moment equilibrium about the center of the…

Q: IF the maximum tension T that the string can sustain is 2/2W then choose the correct options. (A)…

A: Moment at end point will be zero. Correct options: A B D

Q: 3. Determine the horizontal AND vertical displacements of joint B using energy method. All members…

A:

Q: P6-1. use the element shown and specify i, y, and dA.

A: Given Data: Dimensions in the figure. The area of element is given as, dA=xdy The expression of…

Q: The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive.…

A: The diagram of the V-belt drive (open belt) is given as, The diameters of two pulleys are given as,…

Q: F8-7. Determine the vertical displacement of joint D. AE is constant. Use the principle of virtual…

A: Given that : Put the values in the table                   MembersLengthP ( kN )AB3 m   ?BC3 m…

Q: The system above is supported by a ball-and-socket joint at point A, as well as cables BC and BD. A…

A:

Q: N W (3) (1) X Y.

A: Calculated the DOF or mobility and highlighted the total number of links including the ground. And…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: The given force in vector is The position vector of the force can be determined as shown below.

Q: 02 - 3. A truss is loaded as shown. Using the knowled ge of statics, derive a set of equations to…

A: Given data: F1=74 kNF2=24 kN Need to determine the known forces.

Q: Determine the wahl's factor of a spring designed to fire a 3kg projectile. The outside diameter of…

A:

Q: 1,2m 1,2m B A K 1,0m

A:

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: 19. What is the equilibrium angle if the 1-1bm rod is 24 in long? Assume all surfaces are…

A:

Q: determine the support reactions (statics)

A:

Q: Make the free body diagram and calculate the reaction efforts at the points with movement…

A: Length, L1=1.9 m Length, L2=3.3 m Length, L3=3.5 m Load, P1=75 kN Load, P2=140 kN

Q: Using the equilibrium concept, calculate the magnitude of F1 and its direction ф as shown in the…

A:

Q: Now that we've found the force F12, which equilibrium equation will allow us to find the force F13…

A: