Explain the operation of Buchholz relay.

Q: What is the function of Relay?

A: Relays are electric switches that use electromagnetism to convert small electrical stimuli into…

Q: Define Locked in loads

A: Load  - A load is a mechanical stress , moment or couple that a mechanical body is subjected to…

Q: Define the following, Joint. Link. Joint space. Actuator space.

A: Joint: A point where two or more than two links are connected is known as joint. Link: It is a…

Q: Explain the installation procedures of a flexible coupling

A: given; explain the installation procedures of a flexible coupling.

Q: Explain the working of a reverse-air baghouse?

A: There are two styles of reverse air baghouses. More common nowadays, especially with fibrous dust…

Q: Explain with the aid of schematic diagram the working operation of two pressure valve and shuttle…

A: Twin pressure valve: Draw the schematic diagram of the twin pressure valve.

Q: DIOCK orce experienced by both the

A:

Q: Discuss with the help of Block diagram how the power in the wind is converted in to electrical power…

A: WECS ( wind energy conversion system ) :  It is a system by which wind's kinetic energy is converted…

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: Explain the parameters that help to make the driveshafts lighter and efficient

A: Aluminum driveshafts are great for a few reasons. First, they're a lot stronger than the stock…

Q: Define sensors and list the various specifications that need to be carefully studied before using a…

A: Sensors It is a device which converts signals from one energy domain to electrical domain. The…

Q: Name and describe the two principal types of conveyor holdbacks

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: write discussion about to determination of the capacity of a belt conveyor.

A:

Q: Define the term in theory of macines Meyer's expansion valve

A: The Meyer's expansion valve consists of two valve known as  main valve and expansion valve which are…

Q: Difference between ESW and EGW

A: Both the Electroslag welding and Electrogas welding are almost identical with similar kind of…

Q: e power output from

A: Need to calculate the power output.

Q: he belts and rope drive is one of the links which is aving in Es link.

A: Which type of pair in belt drive.

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: List two types of grinders used by welders.

A: welding is a joining process in which two metallic pieces are jointed with the help of heat or…

Q: If 4 links are connected at the same joint, the joint is equivalent to binary joint.

A: This question is from theory of machine.  Here given is that 4 links are joined at a one connection…

Q: Enlist the names of places on aeroplane where the pitot-static tubes are located.

A: A pitot-static system is a setup comprising of pressure-sensitive instruments and is mostly used in…

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: .Explain belt driven starters and mention its advantages

A: Belt driven starters A belt driven starter motor system used to start an internal combustion engine.…

Q: erence between a point loa

A: Difference between point load  and distributed load

Q: introduction about Control of Single and Double Acting Cylinder

A: A single-acting cylinder in a reciprocating engine is one in which the working fluid only…

Q: What should you do if you have to leave a piece of hotmetal unattended?

A: A responsible person should mark any hot metal with "HOT" before leaving the office in order to…

Q: The PWM duty cycle of almost 70% means

A: The PWM duty cycle means as on-time to the period of time.

Q: If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and…

A:

Q: What kind of material is used in the waterless groundloop in a waterless, earth-coupled, closed-loop…

A: Material Used in the  waterless, earth-coupled, closed-loop geothermalheat pump system?

Q: Determine the number of prismatic joints

A: 1. Option (c) 1  is correct option  Explanation: The slider pair is called prismatic pair. Because…

Q: Guve the safety procedure on this process

A: The shaper machine is a reciprocating machine that is mostly used to create horizontal, vertical, or…

Q: Explain why all the fuel in a nuclear reactor is not placed in a single fuel rod

A: The fuel in a nuclear reactor is not placed in a single fuel rod due to following reasons:   a. The…

Q: Explain how to thread FCAW wire.

A: FCAW (Flux Cored Arc Welding): It is a type of semi-automatic arc welding in which a continuous wire…

Q: List the advantages of having one ignition coil percylinder.

A: The timing at each cylinder may be adjusted independently, the saturation time and the interval…

Q: What is a two-force member? Illustrate schematically.

A: This question is based on the concept of two force member.

Q: A So Find tension in AC and BC Hoola

A:

Q: Transmission angle is the angle between and link of a four bar mechanism

A:

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.