Exercise 2. An RCL circuit contains an aging battery generating E(t) = 10e-t/100 volt. The resistance is 100 ohm, the inductance is 2 henry, and the capacitance is 0.001 farad. If initial charge and initial current are zero, find the charge q(t) on the capacitor for t> 0 and sketch its graph. When does the maximum charge occur?

Exercise 2. An RCL circuit contains an aging battery generating E(t) = 10e-t/100 volt. The resistance is 100 ohm, the inductance is 2 henry, and the capacitance is 0.001 farad. If initial charge and initial current are zero, find the charge q(t) on the capacitor for t> 0 and sketch its graph. When does the maximum charge occur?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
In reference to the load, how are capacitors connected to help prevent voltage spikes and surges? Are capacitors connected in parallel or in series with the load?
A 20-ohm resistor and a capacitor are connected in series with a battery of 60 volts. At t = 0, there is no charge on the capacitor. Find the capacitance if the current at t = 5 seconds is 3/e^s amperes. Ans. 0.05 Farads
Q19. For the series-parallel inductor circuit shown in figure B19, answer the following questions. L2 2mH 4mH L3 L4 SMHS 5mH 3.5mH L6 8mH L7 2mH L3 4.5mH e Figure B19 Determine the inductance, L3 value. ii) If E is the energy stored in inductor for current, Calculate the energy if the current value is increased twice.
Calculate capacitance Cand voltage U over resistance. What is the peak value of resistance's voltage? Voltage source e(t) = ésin(wt + 45°). Resistance R-50, circuit's total reactance X-50, inductance L =50mH, ê -40V and frequency f =50Hz. R L Give the answers to one decimal place. Do not write numbers in the complex number form! Absolute value of voltage source (RMS value): V Total impedance of circuit (absolute value): Capacitance: μF Absolute value of current (RMS value) supplied by voltage source: Phase angle of current: degrees Peak value of resistances voltage: 22 A
The network Nc shown below in Figure 1.99(a) contains a combination of scaled capaci- tors in series and parallel connections. Using the vahues as shown, you are asked to do the following. (a) Calculate the value of the terminal capacitance Cab at terminals a-b. (b) To obtain an equivalent capacitance Ceq of 1.5F, Nc is to be placed either in series with a capacitance Cz as shown in Figure 1.99(b) or in parallel with Cx as shown in Figure 1.99(c). Determine which connection is correct and calculate the value of C; that will produce the value of 1.5F for Ceg- 4F 2F 3F 1F C OF (a) N. N. 2. (b) (c) Figure 1.99 (a) Capacitor combo Nc (b) Nc in series with C, (c) Ne in parallel with C,
An inductor is constructed by winding a coil of 100 turns around a magnetic core. The core is a cylinder with radius 0.5 cm and the core material has relative permeability of 1000. The coil covers a length of 10 cm. Determine the resulting inductance. Enter your answer in mH rounded to two decimal places.
Calculate capacitance Cand voltage U over resistance. What is the peak value of resistance's voltage? Voltage source e(t) = êsin(wt + 45°). Resistance R=5N, circuit's total reactance X=5, inductance L=100mH, ê -40V and frequency f =50Hz. L R Give the answers to one decimal place. Do not write numbers in the complex number form! Absolute value of voltage source (RMS value): Total impedance of circuit (absolute value): Capacitance: μF Absolute value of current (RMS value) supplied by voltage source: Phase angle of current: degrees Peak value of resistances voltage: 2 A
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
Draw block diagrams for each of the following elements, first voltage as input and current as output, and then vice versa: a. resistance, b. capacitance, c. inductance.
91)Give Short Ansaers:- a) Determine the dimensions of and Inductance. 2) Differentiiate classi Fication used c) Difine resoluticn one Capacitance between different for Absolute standards Electrical measurinents accuracys and elror example each,
Consider the Capacitance = 10uF, Vpeak of +13v during the positive half cycle and -7v during the negative half cycle. If we have a charging time of 18ms, calculate the Forward Resistance of the circuit in ohms. Calculate the Vout during the negative half cycle. Calculate the Vout during the positive half cycle. Calculate the Discharging time of the circuit in seconds.