Excercise 1: Calculate the maximum acceleration (in units of g) of a pickup stylus reproduicing a frequency of 16 kHz; with an amplitude of 0.01 mm. [Ans: 10,302 g] Excersise 2: Calculate (a) the amplitude and (b) the phase constant for the vibration give by x = (10 mm) cos at + (17mm) sin at [Ans: (a) 19.7 mm (b) -600 ]

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: The strength of solid shaft is of hollow shaft of same weight. the strength

A: The torque transmitted by the hollow shaft is more than a solid shaft for the same weight and…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: Impact velocity equation

A:

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: What is the radius of the blades, if the height of the blades is 0.1636 and the hub diameter is 0.42

A: The height of blade is The hub diameter s

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: Statics; working

A:

Q: Write a note on different types of gear along with application.

A: The gears are used for power or torque transmission. They are generally used whenever the positive…

Q: Determine the magnitude of the resultant force FR = F₁+F₂ and its direction, measured clockwise from…

A:

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: how would you adjust the horizontal plane

A: The horizontal plane is a geometric plane that is perpendicular to the direction of gravity and…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What is the frictional Force

A:

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: Draw the neat diagram of shaper machine and label all its parts.

A: Given:- Shaper machine To find:- To draw a neat sketch of the shaper machine and to label it

Q: Puncher 20 mm o 25 mm thick Punched out F 10 20 mm 25 mm

A:

Q: Wheels of an airplane are made of

A: Solution:

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: Is this for number 1 only?

A:

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: What is the sliding block?

A: To Define: Sliding block

Q: in speed during bending why are you multiplying the speed during bending by 5/18

A: To answer: Why speed is being multiplied by 5/18.

Q: This was not correct may you please

A:

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.