Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm 250 mm 240 N 125 mm

Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm 250 mm 240 N 125 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beam cross section shown below has been proposed for a short pedestrian bridge. The cross…

Q: Q2: A: Find the maximum value of (p) that can be applied to the beam shown. = 350 MPa (WD.L is…

A: We have to determine the value of p that we can apply to the beam shown. Given data fc= 21.7 MPa…

Q: The beam cross section shown below has been proposed for a short pedestrian bridge. The cross…

A: Given: A beam cross section details subjected to shear force Required : Shear stress at point H…

Q: 3. Calculate the value of F and the value of theta 0 so that the resultant of the forces is 1200 lb…

A: GivenRx=0Ry=-1200lbso,Equilibrium along…

Q: It is known that the y-component of the force F exerted on pin P is 37 lb when = 28° and 3 = 11°.…

A: Fx = -11.31 lb The magnitude of answer is correct. Just add the negative sign before the answer.

Q: Current Attempt in Progress The beam cross section shown below has been proposed for a short…

Q: Two identical rods support the loads as shown. The diameters of the rods is 0.8 in. E = 29 x10³ ksi.…

Q: 0.3 m. 120° 60° 0.25 m

A: Angle made by the force with the x-axis, Angle made by the force with the y-axis, Angle made by the…

Q: O 1 m 600 N 2 m- 45° 2.5 m 500 N 300 N

Q: One of the cranks of a child's bicycie is shown. The entire crank lies in the xy plane. Take F= 90…

Q: Please calculate the deflection-y at point 5, and the deflection-x at point 2 based on the following…

A: ####Calculation of deflection Y at 5 and Deflection X at 2 Using Unit load Method of Analysis ####

Q: Calculate the moment of inertia about centroidal axis.

A: In the given image, b=159 mm d=216 mm t=37.4 mm

Q: y F = 25 kN P = 75 kN 6 cm. 4.8 cm 2.4 cm '4 cm 3.6 сm 10 cm

Q: A non-prismatic rod is attached between two supports as shown in figure. It is subjected to axial…

A: Given :- E =200 GpaAAB= 300 mm2 =450 mm2

Q: The beam cross section shown below has been proposed for a short pedestrian bridge. The cross…

A: Given data Shear force (V) = 225 KN = 225 × 103 N Iz = 325870000 tw = 14mm

Q: determin the moment of inertia of the figure shown with respect to the horizontal centroidal axis

Q: The beam in Figure 1 is supported by three cylindrical floaters. The beam is loaded by a load G,…

Q: 2.1.5

A: To determine the moment of the force F about point A , we use the cross product:MA=r×Fwhere r is…

Q: The curved rod lies in the x-y plane and has a radius of 3 m. If a force of F = 80 N acts at its end…

A: Given Data : F= 80 N Radius = 3m Determine the moment of that force = 80 N about point O?

Q: The moment of the following * force about point O is

A: To find the moment of a force, the formula is as follows Moment = Fperpendicular x Distance from O…

Q: 20° F= 10 N 250 mm B 60° 37.5 mm

A: Draw FBD: ∵v250=sin60ov=250sin60o=216.5 mm∵vu=tan60ou=216.5tan60o=124.9 mmtotal vertical…

Q: F = 420 lb I -x, ft | 200 A (7,-3)

A: F=420lbA3,1,ϕ=20∘ =180-20 =160∘ X components of F=Fx=Fcosϕ=420cos160…

Q: 3. Determine the components of the resultant force and the magnitude of the resultant. x = 20 m, y…

Q: Resolve the Force F1 into components acting along the u and v axes and determine the magnitudes of…

Q: c(kn/m)=3 / d(m)=3.5 PLEASE WITH EXPLANATION 2) Calculate the internal forces at the cross section…

A: Given:- The magnitude of the load applied on the beam = c (kN/m) = 3 kN/m Each span length = d (m) =…

Q: A. magnitude of the couple moment Mc so that the equivalent system is a single force acting at point…

Q: The 13 kips force F acting on the simply supported beam. Determine the y component of F?

A: The 13 kips force F acting on the simply supported beam. Determine the y component of F?

Q: The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INa = 30x106…

Q: SIT: A highway curve has the ff. technical description: Radius of central curve = 300m Length of…

A: Radius of central curve, R=300 m Length of spiral, ls= 52.1 Intersection angle of two tangents,…

Q: A beam with rigid support at A, pin connection at C and roller at D has the geometry and loads as…

Q: Determine the force F that could keep the body in equilibrium as shown. What should be the value of…

A: To find magnitude of force F

Q: Find the moment (Nm) acting at O due to all forces and couple present in the following system if P =…

A: An arrangement of cantilever beam is given and it has been asked to determine moment at o which is…

Q: A propped cantilever beam is loaded by a bending moment of the magnitude MB at the point B as shown…

Q: Determine the magnitude(lb) of the vertical component of force at point C if P = 151 lb, x = 13.2…

Q: by two rods which are made of different f elasticity of 29 000 ksi and Rod B is mac 500 ksi. If the…

Q: If the resultant (single equivalent force) of the two forces and couple M passes through point O,…

Q: 600 mm 600 mm -x 300 mm

A: Finding out moment of inertia about x axis and y axis.

Q: A cantilever beam is 4m long with a EI = 20MNm^2. It has a point load of P=1kN at the free end and a…

Q: A trapezoid is shown in the figure. 6 6 6 6 6 Compute the area of the trapezoid. 2 Compute the…

Q: It is known that the y-component of the force F exerted on pin P is 17 lb when 9 = 28° and 3 = 14°.…

Q: Q.4: Consider the shaft shown attached between two walls A and E. Determine the two torques at…

Q: Q3 The board is supported by cables BD and BC as shown. Find the tension force in cables and…

Q: From distance x = 0 to x =4m, the slope of the moment diagram is equal to 0.50x. The change in…

Q: ermine the moment of inertia Ix with respect to its centroidal axis parallel to side AB. ere: h1 =…

A: To find moment of inertia

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

CH2- Resultant pat - aohe Acrobat Pre Extended
File Edit View Document Comments Forms Tookk Advanced Window Heip
M=148 Nmttw
Example Replace the three forces acting on the bent beam by a single equivalent
force R. Specify the distance x from the point O in which the line of action of R
passes.
200 N
160 N
250 mm
--x
250 mm
250 mm
240 N
125 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:The free body diagram of the beam:

VIEW

Step 2:The resultant force will be:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

LUNSTruetiBA PPOJECE Management 2021 Homework3: Draw the network diagram by using AON technique for the following activities, define the located activities on the critical path, define the total project duration, and find all of ES, EC, LS, LC, TF, and FF. Activity Precedent Duration, Weeks 3 B 4 А, Е C, L, M, N A B, C, E, I, J, K, S 1 E F G A В, С, Р B, C, H, O B, C, G, O B, C, E, I, Q F, H, I, J, K, R B, C, F, H, I, J, R 1 I 1 5 K 1 3 10 10 Q R 10 20 B, C, I, O 2.
Determine the x-, y-, and z-coordinates of the mass center of the body constructed of uniform slender rod. 4.8" 1 7.6" 8.0" Answers: ALA x = i y = i Z= in. in. in.
7
300 mm 100mm -200 mm -200 mm Determine the internal forces acting at point Q. Take m= 100kg.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 171660000 mm4. If the beam will be subjected to a shear force of V = 175 kN, determine the shear stress at point H, located at yH = 100 mm above the z centroidal axis.
Subject: Statics of Rigid Bodies Note: Unclear value here is = 3.0000
strictly don't copy ,Make it simple and solve fast
2. The forces F1, F2, and F3 act as shown. Find the x, y, and z components of each force, and the resultant force. Express the resultant force as its magnitude and its angles with the respective x, y, and z axes, a, ß, and y. F₁ = 90 N Z F3 = 200 N 60° F₂ = 150 N 45°
For the figure shown, let a = 200 mm and b = 95 mm. b/2b/2 a e a/2- - a/2→ Calculate the moment of inertia about the x-axis.
The forces shown are applied to the pins at B and C, respectively. Calculate the magnitude of the pin reaction at F. Neglect the weights of the members. *Write your answer in two decimal places. 70KN C. 5m 30KN E 2 m 2.5 m 1.5m F భంగ 6m ద ఉ
Determine the resultant of the three forces as shown in the image.
Locate the x coordinate of the centroid of the beam’s cross-sectional area, and then determine the moment of inertia of the area about the centroidal y prime axis. with complete solution