Example Problem: In figure below, water at 10°C is flowing from section 1 to section 2. At section 1, which is 25 mm in diameter, the gage pressure is 345 kPa and the velocity of flow is 3.0 m/s. Section 2, which is 50 mm in diameter, is 2.0 m above section 1. Assuming there are no energy losses in the system, calculate the pressure P2. Total head

Example Problem: In figure below, water at 10°C is flowing from section 1 to section 2. At section 1, which is 25 mm in diameter, the gage pressure is 345 kPa and the velocity of flow is 3.0 m/s. Section 2, which is 50 mm in diameter, is 2.0 m above section 1. Assuming there are no energy losses in the system, calculate the pressure P2. Total head

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show the necessary figures (if applicable) 2.3) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Given a three-pipe system, the total pressure drop is P,- P, 150,000 Pa, and the elevation drop is Z, - Z, = 5 m. The pipe A data are: Pipe L, m d, cm E, mm eld 1 100 8 0.24 0.003 2 150 0.12 0.002 3 80 4 0.20 0.005 The fluid is water (density 1000 kg/m' and kinematic viscosity 1.02x10 m/s). Calculate the flow rate Q in m'/h through the system. 3
Given a three-pipe system, the total pressure drop is PA - PB = 150,000 Pa, and the elevation drop is ZA ZB = 5 m. The pipe data are: Pipe 1 2 3 L, m 100 150 80 A. O 0.00283 m³/s O 0.00146 m³/s The fluid is water (density 1000 kg/m³ and kinematic viscosity 1.02x10-6 m²/s). Calculate the flow rate Q in m³/h through the system. (3 O 0.00675 m³/s O 0.00834 m³/s d, cm 8 6 4 1 €, mm 0.24 0.12 0.20 2 eld 0.003 0.002 0.005 • B
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in the figure below. f = 0.0161 h1 = 5.95 m h2 = 12.10 m L1 = 69 m Required Compute the pressure at point B in kPa to the nearest 10th, considering the energy loss due to friction, but neglecting other losses. 1.5 m h1 100-mm OD x 3.5-mm wall h2 copper tube Flow B L1
PROBLEMS ON FLUID FLOW IN PIPES 1. What is the hydraulic radius of a rectangular air duct 300mm by 500mm? 2. Air at 1500kPa absolute flows in 25mm-diamter tube. What is the maximum laminar flow rate. Use density of air=14.04kg/cu.m and u=0.0000217Pa-s 3. The flow rate of water through a cast iron pipe is 5000GPM. The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe 4. A tube 15m long is to connect two large tanks whose difference in water level is 2m. The tube is to carry 5L/s of flow. What minimum size of tube is necessary to assure laminar flow condition? 5. The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07cu.m/sec. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.033 and 0.022…
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
A horizontal Venturi flow meter consists of a converging-diverging conduit as indicated in the figure below. The diameters of cross sections (1) and (2) are D₁ = 5.9 in. and D₂ = 4 in. The velocity and static pressure are uniformly distributed at cross sections (1) and (2). Determine the volume flowrate (ft³/s) through the meter if p₁ - P2 = 3 psi, the flowing fluid is oil (p = 56 lbm/ft³), and the loss per unit mass from (1) to (2) is negligibly small. Q= i ft³/s D₁ Section (1) Section (2) D₂
An ideal fluid with y = 8825 N/m flows in the vertical circular pipe represented below. The flow rate Q = 60 1/s, compute the pressure difference between section A and section B. Flow direction D = 0.25 m 0.1 m 0.7 m 0.3 m B D = 0.1 m
Shown in figure, A pump discharged 0.05 cu. m/sec. water from a 220 mm suction pipe and delivers it to a 160 PUMP mm discharge pipe. At A in the 30m suction pipe, the pressure is 50 KPa. PA=50KPA At B that is 30 m above A, determine 220 mm the pressure. If the horse power applied by the pump is 30 HP., head loss equal to 2 m.
Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 97.1 kPa. The gage pressure at section (1) is 103 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 103 kPa, V₁ = 4 m/s. (a) Kx = i 2260.24 (b) to the left N V₂ 160 mm Section (2) 300 mm V₁ Water Section (1) P1 V₁
A water siphon having a constant inside diame of 3 in. is arranged as shown in the figure below the friction loss between A and B is 0.8V²/2 wh is the velocity of flow in the siphon, determine flowrate involved. Assume a = 4 ft, h = 12 ft. D-- B a h