Example 4: Four-wheeled trolley car of mass 2500 kg runs on rails, which are 1.5 m apart and travels around a curve of 30 m radius at 24 km/hr. The rails are at the same level. Each wheel of the trolley is 0.75 m in diameter and each of the two axles is driven by a motor running in a direction opposite to that of the wheels at a speed of five times the speed of rotation of the wheels. The moment of inertia of each axle with gear and wheels is 18 kg- m?. Each motor with shaft and gear pinion has a moment of inertia of 12 kg-m². The center of gravity of the car is 0,9 m above the rail level. Determine the vertical force exerted by each wheel on the rails taking into consideration the centrifugal and gyroscopic effects. State the centrifugal and gyroscopic effects on the car.

Example 4: Four-wheeled trolley car of mass 2500 kg runs on rails, which are 1.5 m apart and travels around a curve of 30 m radius at 24 km/hr. The rails are at the same level. Each wheel of the trolley is 0.75 m in diameter and each of the two axles is driven by a motor running in a direction opposite to that of the wheels at a speed of five times the speed of rotation of the wheels. The moment of inertia of each axle with gear and wheels is 18 kg- m?. Each motor with shaft and gear pinion has a moment of inertia of 12 kg-m². The center of gravity of the car is 0,9 m above the rail level. Determine the vertical force exerted by each wheel on the rails taking into consideration the centrifugal and gyroscopic effects. State the centrifugal and gyroscopic effects on the car.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When do stress concentrations occur?
I need the answer as soon as possible
Quèstion 5 "If we push the book on the table, it stops after sometime. Why?"
Texts: A haulage gear is driven by a motor which develops 15 kW at a full speed of 750 rev/min. The haulage drum is 1.5 m in diameter, and the total reduction ratio of the gearing between the motor and drum is 15:5. The efficiency of the gear is 75 percent, the gradient is 1 in 25, and the rail friction is 135 N per tonne of load. The masses of the gear are equivalent to a total mass of 2.3 Mg, with a radius of gyration of 0.5 m at the drum shaft. Calculate the total load that can be hauled at the full speed. If the motor can give an excess torque of 10 percent of that at full speed, calculate the acceleration possible, assuming that the efficiency and rail friction values remain unaltered.
Please solve for me handwriting request to u please solve all for me what i ask i requested to u solve all handwriting thanks ?.
a) Given is a penstock with deflection and subsequent cross-section reduction. Determine the pressure loss (in bar!) between points 1 and 2 as a result of local losses and changes in cross- section for Q=1001/s. The loss coefficient of the manifold ise.gx=0.5; is the loss coefficient of the neckdowne.g=0.3 Frictional losses are not to be taken into account. notice. All dimensions in mm!
Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
Please give me the answer
give a steps by steps explanation of the solution
kindly Solve it with detail . Graph of Cross section is also given below the question this is complete question . Thanks
Problem 3: A small gearing system in your brand-new 3D printer fails as you were printing, leading to an overload in the motor and a fire in your home. The fire spreads, burning half of Everglades National Park in the worst environmental disaster in US history. The printer company blames you! Stating that you must have been misusing the printer some- how. Use your engineering knowledge to "show those jerks you mean business!" You investigate and find a serial number on the gears and type it into Google, finding the company that manufactures the gears. Their website provides some info that this series of gear is made from AISI 4340 steel and the yield strength is 125 kpsi. Assuming each gear tooth acts as a small cantilever, prove to the 3D printer company that they are liable for the fire. oct # Gear Information Gear radius (r): 1.00 in Tooth length (1): 0.15 in Tooth height (h): 0.15 in Tooth thickness (b): 0.1 in Angular velocity (w): 0.1 rad/s Motor Information Power (H): 0.009 hp 1…
Please answer ASAP! Please show the complete solutions. Rate will be given. No long explanation needed. Answer in 3 decimal places. Mechanics of Deformable Bodies A steel circular shaft (G= 80 GPa) of constant diameter of 28 mm is subjected to the following torques in N-m: TA= 160; TB = 130; TC = 350; TD = 380. The directions of the applied torques are indicated in the figure The bearings shown allow the shaft to turn freely. The length of each segment is equal to 86 cm. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torque. Use the same rule of signs as in the lecture. Determine (b) the maximum stress in the shaft in MPa (C) rotation angle of pulley B with respect to pulley D. Solid shaft: J= (pi/32 X D4) Hollow: J= (pi/32xD4-d4) Note: Please Follow rule of signs and show complete FBD of each section