Example: 1.16 A moving coil instrument gives a full scale deflection of 10mA, when the potential difference across its terminal is 100mV. Calculate (1) The shunt resistance for a full scale deflection corresponding to 100A (2) The resistance for full scale reading with 1000V. Calculate the power dissipation in each case?

Example: 1.16 A moving coil instrument gives a full scale deflection of 10mA, when the potential difference across its terminal is 100mV. Calculate (1) The shunt resistance for a full scale deflection corresponding to 100A (2) The resistance for full scale reading with 1000V. Calculate the power dissipation in each case?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

4. WHAT IS MUTUAL INDUCTION AND SELF INDUCTION. WHAT IS THE UNIT OF INDUCTANCE.
An iron ring elecromagnet has a relative permeability of 1250 when it is excited by a coil having 500 turns at 0.8 A. the mean length of iron parts is 48 cm, the cross-section of the core is 10 square cm and the air gap is 0.5 cm. What is its total reluctance?
what is the use of DC/DC tension converter DC/DC booster MT3608
Diodes Are Connected In Series To Share A Total... 21 Question • Two diodes are connected in series to share a total reverse voltage of VD=D 5 KV. Reverse leakage currents of the diodes are ID1=30 mA and Ip2=35 mA. - Find Vp1 and Vp2 for R,=R2=100 k2 - Find R, and R2 for VD1=VD2 R1 VD1 Hint: Is=L,+IRj= I,2+IR2 VD R2 VD2
a/ What is the function of the inductance L in a single phase halfwave thyristor? b/ A controlled full wave bridge rectifier has a source of 50 Sinwt with R = 10 and L = 20 mH find the d.c load current if a = 40°, then draw Vo and lo use 50 Hz freq. and B = 1.1n %3D
Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.
LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity of LVDT please explain me
0) A full-wave controlled rectifier with RL load is shown in figure 8. If the firing angle is 70° and the average load current is 20A, find the transformer ratio (N/N). V,-v2 x200 Sin314 100MH Figure 8 w
A platinum coil has a resistance of 3.146 at 40OC and 3.767 at 100OC. Find the resistance at 0OC and the temperature –coefficient of resistance at 40OC. Major Topic 8 Temperature coefficient of resistance EV Sco
Question 14 In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL = 1 KQ. Not yet answered Assume diode as Germanium and the input frequency is F= 50HZ. Marked out of Dy 3.00 P Flag question RL D, 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. B I 00000
Q: - Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. 4:1 D, 120 V rms c) If sin wave with 100µf connected in parallel with the resistor, calculate the ripple сарacitor is 60 HZ 1.0 kN D2 factor lllee lelll
t n. Determine the output waveform for the network below and calculate the output dc level and the required PIV of each diode. Assume supply of 100Vac,D2 and D3 are germanium diode, D1 and D4 are silicon diode and 1:2 center-tapped transformer. 120Hz www 1k