Please help me with 100% correct solutions ENGINEERING DRAWING EGT35611. A cone with a 55 mm base diameter and a 85 mm long axis, rests on its base on the H.P. Draw thesectional top view and the development of its lateral surface when it is cut by an inclined planebisecting the axis and inclined at 45 to the H.P.2. The cylinder 70 mm diameter and 90mm axes is completely penetrated by a square prism of 30mmsides and 90mm axis, horizontally. Both axes intersect and bisect each other. All faces of prismsare equally inclined to horizontal plane (Hp). Draw projections showing curves of intersections.Dimensioning, title block, neatness, lettering

As per Bartleby guide lines I would like to provide the solution for the first question among from…

ENGINEERING DRAWING EGT3561 1. A cone with a 55 mm base diameter and a 85 mm long axis, rests on its base on the H.P. Draw the sectional top view and the development of its lateral surface when it is cut by an inclined plane bisecting the axis and inclined at 45 to the H.P.

ENGINEERING DRAWING EGT3561 1. A cone with a 55 mm base diameter and a 85 mm long axis, rests on its base on the H.P. Draw the sectional top view and the development of its lateral surface when it is cut by an inclined plane bisecting the axis and inclined at 45 to the H.P.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Based on typical tolerances for the traditional and non-tradibonal manufacturing processes, Identify…

A: Solution: The Tolerance value for the following traditional and non-traditional manufacturing…

Q: Which of the following part designs would be preferred because it would result in lower production…

A: To be explained:- which method will give lower cost

Q: Q4: State the advantage of electro polishing over mechanical polish

A: This question is based on the concept of electropolishing.

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: Tell us about the tolerance zone in operations.

A: As per given we have to detail describes about tolerance

Q: pes o

A: GIVEN: Explain different types of fits?

Q: what would be the order of operation to make this part on a virtical mill and what would be the…

A: Note: As you have posted multiple question, i will be answering first question. Please resubmit the…

Q: How production enhancement is done using artificial lift?

A: Basically artificial lift is used to help lift production to the surface and it can include methods…

Q: A datum when used in manufacturing is primarily used for?

A: A datum in manufacturing is defined as the origin point, plane, or axis from which the geometric…

Q: Which of the following statement is correct? O Discontinuities can propagate and become defects. O…

A: ◆ The discontinuity is the imperfection on the physical surface of the objects. The examples of…

Q: Limit Gauge loose fit, slide fit, easy sliding fit, running fit Go & No Go Ends O the difference…

A: As per our guidelines we are supposed to answer only one question if multiple questions are asked.…

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2. There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: Tool forces are generated by the fixture or jig during a machining cycle O True False

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Propose any improvements if there are any in breaking system

A: The various improvements that can be made in a breaking system are given below. 1. Increasing disc…

Q: need answer within 20 minutes please please with my best wishes

A: Superfinishing is different from honing in a way that:- In honing the small removable of material…

Q: If you were manufacturing a component with a minimum thickness of 1mm and a tolerance of 0.1mm (or…

A: The provided thickness and tolerance of the part are as shown below. thickness = 1 mm tolerance =…

Q: A certain type of cans are formed on a machine by spinning them from cardboard stock and attaching a…

A: Given \ Sample size N=50 Total number of samples is M=30 Table1: Number of nonconforming cans in a…

Q: 1: How is the size of the abrasive grain chosen?

Q: Describe the concept of finding toughness using impact testing machine.

Q: We need to purchase .50” thick foam with a tolerance of plus or minus 10%, what is the maximum and…

Q: ne or more can be correct please select from below options Lower operating temperatures are more…

A: In the moulding process known as compression moulding, a feeding material is inserted into an…

Q: 1. Cover page of the project 2. Table of the content 3. Abstract 4. Introduction 5. Detail machine…

A: MANUFACTURING PROCESS It is a value addition process ,manufacturing is process of converting raw…

Q: In exponential smoothening method,

A: Given; Exponential smoothening method, Which one of the following is true,Where, Exponential…

Q: 3x – 2

Q: What is line of impact?

A: The line of impact is the line along which the impact forces act during the collision. Generally, it…

Q: How productivity of a well is done and which techniques/test you incorporate

A: Productivity of a well is measured using well test. It is a necessary practice in oilfields used to…

Q: Q2: Can cBN be used in honing stick in single layer configuration?

Q: Give me the process of making a meat tenderizer using a shaper machine process. The picture below is…

A: As we know that it is a tool controlled by hand which makes mellow pieces of meat for cooking.

Q: 1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil…

A: To decrease the friction losses in the bearing oil is used .varios types of the oils are used for…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: Unilateral tolerance is one in which the variation from the specified dimension is permitted in only…

A: Unilateral tolerance is one in which the variation from the specified dimension is permitted in…

Q: Estimate the manufacturing cost for a simple machined component: a. Compare the costs for…

A: To Compare:a) The costs for manufacturing volumes of and pieces with an intermediate tolerance and…

Q: QUESTION 4 External failure quality costs occur when customers discover a defect. Which of the…

Q: B. A machine - part needs 14 bolts a How many bo43 are needed For 25 nachine -parts? b. wnat is the…

Q: Draw a product structure tree for a rolling cart using the low-level coding scheme.

A: Given data: they given items and components and they ask to draw product strycture tree

Q: If you were manufacturing a precision component which has a mass of around 15 grams and which was a…

A: ans : Low pressure casting Solid 3D objects made by low pressure casting all other option are…

Q: Please guide me through the procedure of thoroughly testing individual components.

A: The procedure of thoroughly testing individual components.

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

Please help me with 100% correct solutions

ENGINEERING DRAWING EGT3561
1. A cone with a 55 mm base diameter and a 85 mm long axis, rests on its base on the H.P. Draw the
sectional top view and the development of its lateral surface when it is cut by an inclined plane
bisecting the axis and inclined at 45 to the H.P.
2. The cylinder 70 mm diameter and 90mm axes is completely penetrated by a square prism of 30mm
sides and 90mm axis, horizontally. Both axes intersect and bisect each other. All faces of prisms
are equally inclined to horizontal plane (Hp). Draw projections showing curves of intersections.
Dimensioning, title block, neatness, lettering

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is compression testing?
Why 100% of the total material is not possible for 100% sampling
Sub: Advanced Manufacturing Process
What is abrasion resistance testing?
what type of grinding wheel should be used to get the required finish on this part using a surface grinder?
what is the range of gear sizes can be achieved by forging, extrusion and metal removal processes.
Quèstion 25 Which of the following describes the effect of shot peening on fatigue life? O A. It has no effect on fatigue life O B. It decreases fatigue life because of increased surface hardness O C. It increases fatigue life because of induced compressive stresses D. It decreases fatigue life because of excessive surface deformation A Moving to another question will save this response. 34°C äolo claw ENG 4)
The term "maintenance" refers to maintaining all of the systems and features in working order. * as close as possible to the original O design purpose of the manufacturer tons as close to the manufacturer's original design purpose as impossible as impossible to the manufacturers original design intent tons. as possible to the manufacturers unoriginal design intent tons skip Punctures are- a small hole in a tire resulting in an get- away of air a large hole in a tire resulting in an get- away of air a small hole in an engine resulting in an escape of air a small hole in a tire resulting in an get- away of oil Skip
What type of porosity is most often caused by mill scale?
Which one of these may increase the amount of contact resistance? Lower temperature during matching of materials decreasing pressure for pressing the materials together Higher surface roughness All of the above Using air as a fluid for the gap instead of liquids