elocity of the jet is 36 m/s. Find the arge Q. 0.6362 m^3/s 0.152 m^3/s 0.1622 m^3/s 0.114 m^3/s

Q: can you explain why in solving for d the 2.5in was divided by 2

A: Given:- The overall depth of the beam = 30 in The concrete cover = 2.5 in  To determine:- Why for…

Q: For the beam shown in figure, determine the nodal displacements/slopes. 5 kN/m E = 210 GPa I= 2x104m…

A: Given : E = 210 GPA I = 2 × 10^- m4 Solution :

Q: The velocity profile inside the boundary layer for flow over a flat U π plate is given as И со 28…

A:

Q: 13 KN 27 KN/m 86 KN/m 1.71 m 3.79m B. 6.53 m 3.42 m

A: Step 1

Q: r is incorrect again, it should be positive 134.6 kN/

A: Given:- ∅=200qu=140kN/m2 To find:- pore water pressure

Q: 13. A steel tape with a cross-sectional area of 0.03 cm^2 is 30.0 m long under a pull of 5 kg when…

A: Given, Cross-sectional area ,A= 0.03 cm2  Length of tape, l=30.0 m Standard pull, P0= 5 kg  Length…

Q: Q51. Prove that the force exerted by a jet of water on a fixed hemispherical curved vane when the…

A:

Q: The diagram shows the cross-section of a creek, with the depths of the creek shown in meters, at…

A:

Q: 120 KN 1.5 m 70 KN/m 70 KN/m 1.0 m A 3.0 m 3.0 m

A:

Q: Determine the natural frequency of the system shown in the figure.

A: Given data: M = 25 kg E = 200 GPa I = 5x10-7m4 k = 5 kN/m ΕΙ = 4 m

Q: Given the figure below, determine the deflection at B if El is constant 40 kN/m 40 kN/m B A 3 m 3 m

A:

Q: The water behind Grand Coulee Dam is 1 200 m wide and 150 m deep. Find the hydrostatic force on the…

A: Given data: Width of dam= 1200 m Depth of dam=150m

Q: Situation 4: A W6x25 has a length of 5.3 m. Fy= 248 MPa. The properties are given below. Properties…

A: Le = kL = 0.8 x 5.3 m = 4.24 m = 4240 mm

Q: An iceberg (SG = 0.93) is floating on seawater (SG = 1.02). The volume of the iceberg is 50 cubic…

A:

Q: Q.12. The velocity distribution in the boundary layer is given by: 3 1 η n² F V 2 2 y In which n=…

A:

Q: Calculate the elongations in the z and x directions in the block placed in a cavity as in the…

A: Asked: To determine the elongations in the x and z directions.   Given: Poisson's ratio (ν) = 0.25…

Q: A R 2m 2.4P 10.2 kN/m 2m 2m 1.2P ΣΜ.=0 B R(4) - 2.4P(2)+ 1.2P(2) - 10.2(6)1–0 R = 0.6P + 15.3

A:

Q: 35 KN 60 KN/m 37 KN/m 3.60 m A 6.74 m 1.59 m B

A:

Q: By Double Integration, find the magnitude of the midspan deflection. Assume El is constant. 6W…

A: Given  W= 84

Q: , a= 2 m, amd w = 40 kN/m. Use doubl 40 kN/m

A:

Q: Compute for the density of the liquid in kg/m^3.

A: This question is from Fluid mechanics

Q: For the system below, EI is constant. If x = 6.73 m from point B, determine the value of EI(Δ) ?…

A: Deflection of a beam: The spacing between both the role of the beam before and after loading is the…

Q: 36.40 KN 84.80 KN/m 0.565m 0.565m A В 1.13m 8.36m

A:

Q: For the beams below, determine the location of the maximum deflection using double integration…

A:

Q: A laminar boundary layer velocity profile is approximated by u/U= 2(y/6) -2(y/6) + (y/6) for y ≤ 6,…

A: In the velocity boundary layer, the flow velocity is distributed among different fluid layers…

Q: The opposite figure composed of a triangular part ( base =b =10.2 m, height h=5.1 m } , ρ1=3.3…

A: Figure composed of a triangular part and semicircular part. We need to calculate geometric…

Q: 200 KN wot E = 200 G Pa A = 20 cm² 10 m C

A: Displacement ∆=∑PkLAEwhere P=load in member due to applied loadk=force in member due to unit load…

Q: The volume of the frustum of a triangular pyramid is 135 cu. m. The lower base is an equilateral…

A:

Q: For the system below, EI is constant.  If x = 8.12 m from point A, determine the value of EI(Δ) ?…

A:

Q: Using the double integration method, determine the value of the slope at point B and the vertical…

A: Given:Required:Slope at point B, vertical displacement at point A and deformed shape with the…

Q: For the system below, EI is constant.  If x = 8.12 m from point A, determine the value of EI(Δ) ?…

A: Free body diagram -  Force in the vertical direction -  ∑FY = 0 ⇒RA + RB - 27×5.33 - 81 - 57×2.32 =…

Q: 20. A 6-meter simply-supported beam is loade with a 2kN/m uniform load and a 10kN concentrated load…

A:

Q: Opening and loading condition taking into account only the bending effects of the cantilever beam…

A: Given above data we have to displacement by double integration method

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.