dx

Q: Part of the screw thread connecting the adjacent flank on top of the screw thread is known as O…

A: Correct answer is option (b) Pitch  The pitch of a thread is the distance measured parallel to its…

Q: The traffic light hangs from the cables as shown. Draw a free-body diagram on a coordinate plane for…

A: Given data Weight of light =200N Draw the free body diagram

Q: dy = m y2 dx

A:

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: 12-x2 了了少 Je

A:

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: y h с b bh .1

A:

Q: P? P G P

A:

Q: Q/ The moment about the centre of the bolt is 0.2 m 0.03 m O 20.21 N.m O46.411 N.m O 55.626 N.m 300…

A:

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: In this pair number of binary joint is available. O A. four O B. one O C three O D. two

A: A joint is the connection of two or more links at a section. In a fixed or permanent mechanical…

Q: Please solve for the reactions at A

A:

Q: The J-shaped member shown in the figure (Figure 1) is supported by a cable DE and a single journal…

A: Given DataThe cylinder has a weight of WB=5.60lbThe Vertical force applied to member C, F=1.50 lbThe…

Q: 2.000 2.500 000'9 000 000 0007 RO.500

A: CNC PROGRAM G99  G21 G40 S1000 M13 M06 T0101 G00 X5.5 Z0.25 G01 X5 Z0 F0.005 G71 P10 Q20 U0.01…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: What is the moment-area method?

A: The moment-area method is one of the methods for determining the slope and deflection generated in a…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: d W Pm a Ps

A: The free body diagram of the system is showing below –

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: Which is the correct formula for Hook's Law?

A:

Q: F E F to

A: for solution refer below images.

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: 4. (Ef-1 X¡)^2 =D1

A: Sigma indicates sum of ^ indicates power.   In order to solve this, the following equation should be…

Q: choose true or false : -The ratio of linear stress to linear strain is called Modulus of elasticity.

A:

Q: Problem 6.131 Determine the general expression of the acceleration of the piston C as a function of…

A: Write the given data.

Q: choose the correct answer 200 B. G- A Zero Force members

A: We know that if a joint with two members is not subjected t any external load and also that joint…

Q: why12ft was not used?

A: We know that the moment is calculated with respect to the position vector of point of application of…

Q: A 5 ft DU B 5 ft -3 ft-

A:

Q: The handle of the hammer is subjected to the force of 35 Ib. The moment of this force about the…

A:

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: Answers: FA= FB = i i kN kN

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.