During the Wheatstone Bridge experiment, when the pointer is at the balance point then:O a. The potential difference across the unknown resistance is equal to the potentialdifference between the end of the wire connected to the known resistance.the balancepoint.O b. The potential difference across the known resistance is equal to the potential differencebetween the balance point and the point of contact between the known andunknownresistances.O c. The potential difference across the unknown resistance is equal to the potentialdifference across known resistance.O d. The potential difference across the unknown resistance is equal to the potentialdifference between the balance point and the end of the wire connected to theunknown resistance.O e. The potential difference across the unknown resistance is equal to the potentialdifference between the balance point and the end of the wire connected to the knownresistance.Clear my choice

Wheatstone bridge: The figure shown above is the wheat stone bride, It is circuit used to measure…

During the Wheatstone Bridge experiment, when the pointer is at the balance point then: O a. The potential difference across the unknown resistance is equal to the potential difference between the end of the wire connected to the known resistance.the balance point. O b. The potential difference across the known resistance is equal to the potential difference between the balance point and the point of contact between the known and unknown resistances. c. The potential difference across the unknown resistance is equal to the potential difference across known resistance. O d. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the unknown resistance. O e. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the known resistance.

During the Wheatstone Bridge experiment, when the pointer is at the balance point then: O a. The potential difference across the unknown resistance is equal to the potential difference between the end of the wire connected to the known resistance.the balance point. O b. The potential difference across the known resistance is equal to the potential difference between the balance point and the point of contact between the known and unknown resistances. c. The potential difference across the unknown resistance is equal to the potential difference across known resistance. O d. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the unknown resistance. O e. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the known resistance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. A length of a copper telephone line has a resistance of 24 ohms at 20°C. What is the resistance on a hot summer day when its temperature raised by 26C°? 7. A certain cooper wire has a resistance of 25 ohms at 10°C. Take the temperature coefficient at 10°C to be 0.00409/°C. What must be the maximum operating temperature of the wire if its resistance is to increase by most 30%? 8. The resistivity of iron at 0°C and 12°C is 8.68 x 10 *0-m and 9.75x 10 -8 N-m respectively. Calculate the resistivity at 35°C 9. One meter rod of 2 inches diameter is drawn until its resistance is 100 times the initial resistance. Its length afterward is? 10. The substation bus bar is made up of 1.5 inches round copper bars 30 ft long. What is the resistance of each bar? 11. What is the color code for a 8KQ, tolerance + 10% resistor? 12. Find the nominal value of the resistance of the resistor shown.
Thermistor, which has high temperature coefficient of resistivity. is used as the sensing element in resistancethermometer. It is alan:Select one:a. Solid-semiconductor O b. InsolatorO c. ConductorLiquid
1- If we use 5000 μF, we can get a very low ripple voltage. But this is so bad and this a disadvantage, why? 2- What happens if we use a very small resistance (few Ohms) or big resistance (100 kOhms) ?
Answer and write the observation about the problems.
The resistance of a copper wire is (0.92 N) at a temperature of (4 oC). At what temperature will be resistance be (1.06 Q)?
Mention applications of a resistance strain gauge for measurement of non-electric quantities.
aph R₁ 100 ΚΩ R₂ www R₁ 1.0 kn body 1. Determine the necessary value of R2 in Figure 4 so that the circuit will oscillate. Neglect the forward resistance of the Zener diodes. (Hint: The total gain of the circuit must be 3 when the Zener diodes are conducting.) 2. Explain the purpose of R₁ in Figure 4. www. body bold 6.8 V 6.8 V R3 47 ΚΩ R₁ www 1.0 kn 0.015 μF Normal 0.015 µF No Spacing Styles He
interpret the data, describe the graph,describe the curve.
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
I need helpo with this. I need step by step solutions for this and I cant figure it out. Wire to be used in buildings and homes in the United States is standardized according to the AWGsystem (American Wire Gauge). Wires are assigned a gauge number according to their diameter.The scale ranges from gauge 0000 to gauge 36 in 39 steps. The equation for the wire gauge interms of the wire diameter in millimeters is as follows.Answer the following questions with your group.(a) What is the equation for the diameter in millimeters in terms of the wire gauge N?(b) You have two wires, one that has five times the diameter of the other. By how much do thewire gauges differ for the two wires? (Give your answer to the nearest integer.)
I need helpo with this. I need step by step solutions for this and I cant figure it out. Wire to be used in buildings and homes in the United States is standardized according to the AWGsystem (American Wire Gauge). Wires are assigned a gauge number according to their diameter.The scale ranges from gauge 0000 to gauge 36 in 39 steps. The equation for the wire gauge interms of the wire diameter in millimeters is the picture. (a) What is the equation for the diameter in millimeters in terms of the wire gauge N?(b) You have two wires, one that has five times the diameter of the other. By how much do thewire gauges differ for the two wires? (Give your answer to the nearest integer.)
C and D are the correct answers. I just need solutions.