DS D1 Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft. The average weight of each floor and roof are 95 lb/ft2 and 75 lb/ft2, respectively. The 84 ft-tall building is located in a seismic region with S =1.6 g and S=0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor l=1.0 Determine the total design seismic force (kips) acting at the base of the building (seismic base shear in kips)

DS D1 Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft. The average weight of each floor and roof are 95 lb/ft2 and 75 lb/ft2, respectively. The 84 ft-tall building is located in a seismic region with S =1.6 g and S=0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor l=1.0 Determine the total design seismic force (kips) acting at the base of the building (seismic base shear in kips)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The billboard shown is supported by structural tube that has a 380 mm outer diameter and 38 mm wall thickness. If the billboard is under wind pressure Pwind and has weigth of Wbillboard, determine the principal stresses and max. in-plane shearing stress at point H. Assume wind is applying uniform pressure all over the billboard and centroid of the billboard is located at point C. You can ignore the thickness of the billboard. P???? =2.3kPa W????????? =80 kN
8. Determine the magnitude and location of Resultant of the loading shown relative to the free end. 20 N/m EDN/m ON/M 4m 3m 30 N Wb = 25N/m
Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft . The average weight of each floor and roof are 95 Ib/ft and 75 lb/ft?, respectively. The 84 ft-tall building is located in a seismic region with SDs =1.6 g and SD1 =0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor I=1.0 Determine the total design seismic force (kips) acting at the base of the building ( seismic base shear in kips). ***the answer was between 339.5 and 342.5*** but I don’t understand how . Handwritten work is preferred
BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress and the maximum flexural stress of the beam. The cross-section of the beam is 150 mm x 350 mm. A B 10 KN 15 KN/m C 1.50 1.00 1.50 10 KN/m D D.Lopez 2.00 in meters Figure A: Overhanging Beam E
An elevated water tank weighs 3000kN when filled with water, the centroid of the mass being at a height of 9 meters from ground. The horizontal spring factor for the tank tower is 15 kN/mm. Determine the shear force generated at the base of the water tank tower by horizontal seismic inertia force. Assume the ground motion has a period of 2.0 sec and maximum acceleration of 0.15g
Given the ff. data of dynamic lateral force procedure for buildings:Period of vibration: T = 0.8 secSpectral velocity, Sv = 0.15 m/secK = 15 158 kN/mmTotal W = 2400 kN Give the maximum relative displacement,the value of spectral acceleration,value of the lateral force of the tank in kN,the value of the maximum base shear in kN.
Given. A three-story, two-bay SCBF shown in Fig. 3.41. It is part of a building frame system of a structure in seismic design category (SDC) D with a redundancy coefficient p = 1.20. The building is on a site with a short period mapped acceleration response Sps = 0.90. The axial loads acting on the second story brace B2 are Dead load D = 40 kips Live load L = 12 kips Snow load S = 0 kips Hydrostatic load H = 0 kips Seismic force Q = +90 kips Required. Select an appropriate tube section for the second-floor brace B2. Use ASTM A 500, Grade B, F, = 42 ksi, F. (minimum tensile stress) = 58 ksi, steel.
A propped beam of length 6m carries a concentrated load of 130kN, 2m from the fixed support and 40kN, 4m from the fixed support as shown: 2 130 2 40 2 a. Determine the plastic moment if the collapse mechanism occurs under the 130kN load. b. Determine the plastic moment if the collapse mechanism occurs under the 40kN load. c. Determine the plastic moment capacity.
The flat roof of the steel-frame building shown in the photo is intended to support a total load of 2KN/m over its surface. Determine the roof load within region ABCD that is transmitted to beam BC. A B XTE D C 1.5m 2 m 1.5m 2m -4 m 2m B
Situation 6. Determine the resultant force R and its line of action for the following force-couple systems: F = -600 N, F, = 800 N, and C = -24000 N – m %3D
Problem 01: Determine the plastic moment capacity of the continuous beam shown. Use a load factor of 1.75 for the working loads shown. 25KN 13KN 18KN W=8m kN/m 1.50m V 1.50m V V 1.50m A BO DEO F 4.50m 4.50m 3.00m
al answer. 2P 2P 2P 4 m Ew P 4m ان E C 4m STAT-001 A G F -9 m- D NO F@15 80 B