Draw the torsional moment diagram. Determine the torsional angle CA (rotation angle) that will occur at point C. Determine the maximum shear stress that will occur in the system. (G=80 000 MPa) M1(Nm) 9000 M2(Nm)2000 D1(mm) 90 D2(mm) 60 D3(mm) 50 D4(mm) 30

Q: In the figure below, at section n-n (x = 4m from point A) determine shearing stress at a on the…

A:

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b = 5.6 in., d = 5.0…

A: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

Q: 1) In the system given in the adjacent figure, the normal stress that will occur in the a-a section…

A: Normal stress = δn ≤ 150MPaShear stress = T = 60MPaCross section of BC = xy = 53mm

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given data in question  Torque 2410 Nm Outside Diameter D0 75 mm Thickness 5 mm Shear modulus 80 GPa…

Q: A SHORT compressive force as shown in Figure Q3a. (a) column with an I-section is subjected to an…

A: To find out the bending moment about x and y axis and also find out moment of inertia and stress.

Q: 5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

A: Given Data  Shear modulus (G) = 85 GPa  Diameter of shaft (d) = 40mm  Length of AB (LAB) = 0.5m =…

Q: Problem 4 The horizontal force of p 85 kN acts at the end of the plate. The plate has a thickness of…

A:

Q: If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the…

A: Given for CD shaft    diameter d2=35 mm, radius of gear R2=125 mmand torque T2=75 N-mfor EA shaft…

Q: The internal shear force at a certain section of a steel beam is V=7.2kN.  The beam cross section…

A: Given:- Shear force, V=7.2 KN To find:- a Shear stress at point Hb Shear stress at point Kc Maximum…

Q: The stress on a structure is as follows. The EI of the ?-shaped part of the structural section is…

A:

Q: 200 mm If the beam is subjected to a bending moment of M=50KN, determine the maximum bending stress…

A: Using formula to find bending stress

Q: Q1. 1.) Determine the state of stresses at an orientation of 20 degree clockwise from the element…

A:

Q: P = 7 kN 10 mm 15 kN • m 10 mm 150 mm D В C 150 mm 1.0 m →* 1.0 m 1.0 m The simply supported beam is…

A: Given data    P= 7 KN moment at B MB=15 KN-m Using ∑Fy=0                      Va+Vb=7 KN Using ∑Md=0…

Q: 1. The lap joint in Figure 1 is connected by three-20 mm diameter rivets. Assuming at the axial load…

A: Given data in question  Load Diameter  To find out  Shear stress Bearing stress Maximum average…

Q: 4. The cross-sectional dimensions of the beam shown in Figure are d = 5.0 in., br = 4.0 in., tr =…

A: Given:- d = 5.0 inches bf  = 4.0 inches tf = 0.50 inches tw = 0.25 inches  bending stress at point H…

Q: 100 mm Q.2) The right figure show the cantilever beam and loading, while the left figure show the…

A: Solution:- 1. Shear stress in the beam:

Q: (2) (1) Pe с B L2 Li

A:

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

A: Given: A square cross section of 400mm × 400mm Shear force = 150KN Bending moment = 250KN-m…

Q: The stresses shown in the figure act at a point in a stressed body. Determine the normal and shear…

A: Given: Sx=7200 psi Sy=2300 psi  θ=64o  To find: Normal and shear stresses

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given Outside diameter (Do) = 75mm Thickness of wall (T) = 5mm Torque (T) = 1680 N-m Shear modulus…

Q: A 80 MPa 30° B 30 MPa 40 MPa

A:

Q: 10 k Sectian 300 800 ISM P= 300 ku, e = 250mn From the given figure shown, Calculate the stress at…

A:

Q: Q4) (2UMS): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine…

A:

Q: An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft…

A: We will find torque in 1 and 2.

Q: Determine the orientation of principal planes of stress. Enter your answers in degrees to three…

A:

Q: Draw Mohr's circle and find: 1) Principle stresses and their direction. 2) Maximum Shear stress and…

A:

Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…

A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section

Q: The structure shown is supported by a steel rod at B. Specifications of the steel rod L= 2m…

A: Data given: Specifications of the steel rod L= 2m d=25 mm E=200 GPa Asked: 1. Draw the shear force…

Q: The internal shear force V at a certain section of an aluminum beam is 40 kN. The beam's centroid is…

A: V = 40 kN, Location of Centroid from bottom = 54.4 mm, Moment of Inertia, Iz = 398300 mm4

Q: 7. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the value of…

A: We have to determine the value of torque T that can be applied to the ends of the shaft without…

Q: y A 100 mm В 20 mm 150 mm 10 mm 20 mm 100 mm

A:

Q: X- 18 cm Mx y 10 cm 18 cm 3 cm 2 cm 16 cm 2 cm 2 cm 10 cm A bending moment of magnitude M₁ = (6+K)…

A: An I section type beam is given with bending moment = 23 Kn-mAssume the moment is sagging Hence…

Q: 8. A stress element dia is shown in fig. compute the normal. t shear stress on plane. Ar. (a) втрат…

A:

Q: e bending stress about the y-axis at points A e if the stress is in tension or compression. 200kN m…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.