Consider a thin, flat, uniform, homogeneous rectangular plate of sides1200 x 1500 mm, and mass 5 kg. a) Determine area and mass momentsof inertia and radius of gyration about a corner of the plate.Suppose the plate is suspended from a corner and lies at restin a vertical plane when it is subjected to a net constant momentof 3 N.m about the hinge. Determine, at t = 2 s, anywhere in the plate,the max magnitude ofa) Velocity v, and c) Acceleration a.

Given Rectangular Plate of, Length, L = 1200 mm Breadth, B = 1500 mm Mass, M = 5 Kg

Answered: Consider a thin, flat, uniform,…

Consider a thin, flat, uniform, homogeneous rectangular plate of sides 1200 x 1500 mm, and mass 5 kg. a) Determine area and mass moments of inertia and radius of gyration about a corner of the plate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question Bank - Friction The 40-N spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the 130 270 mm 192 mm wire.
üz a aplanmadı ) üzerinden etlenmiş y ioruyu etle Н V The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the first moment of area (Q) for the point H (mm) where L=48,2 mm.
The system shown in the figure has a fixed support at A and an alumimum rod of 0.5m length at C. The beam AC is subjected to a point load of 20 kN at its midspan. In addition to that point load, alumimum rod is subjected to a temperature decrease of 25 °C. Determine the deflection and the rotation at point C. Anhunnd 70 GP in
A 100- m steel tape is used to measure the distance of the line and found to be 1539.28- m long. During measurement, the tape is supported at the ends under a pull of 10- kgs and the observed mean temperature is 31°C. The tape is of standard length at 20 °C and a tension of 12- kgs. Thecross sectional area of the tape is 0.035 cm2. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 (10)^6 kg/ cm2. The tape weight is equal to 1.5- kg. a) Determine the total correction for temperature.b) Determine the total correction due to tension.c) Determine the total correction due to sag.d) What is the correct length of a line?
Q2: A: Find the maximum value of (p) that can be applied to the beam shown. Use f =21.7 MPa and fy 350 MPa (WD.L is included the self-weight of beam). Wu =7 kN/m D.L 2028 500 mm 4028 250 mm -7.5 m- Page 1 of 2 170004
The assembly consists of two 20-mm diameter rods AB and CD, a 30-mm diameter rod EF, and a rigid bar G. The assembly is subjected to the loading shown, with point E located at the midpoint of BD. Take the modulus of elasticity of the rods as 100 GPa. i. Determine the horizontal displacement of point E (indicate direction, left or right). 11. If the applied loads causes the diameter of rod AB to become 20.0022 determine the Poisson's ratio of the material (to 2 decimal places). 350 mm 450 mm A B 40 kN E 60 kN 40 kN DG
The 742-N force is applied to the 117-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂=0.83 Hk = 0.59 Answer: F = i 28° N P = 742 N
The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A. Determine the force P required to begin pulling the wire horizontally off the spool. The coefficient of static friction between thespool and its points of contact is μs = 0.25.
3. A rigid bar is supported by two rods which are made of different materials. Rod A is a steel rod which has a modulus of elasticity of 29 000 ksi and Rod B is made of bronze which has a modulus of elasticity of 14 500 ksi. If the bar is horizontal before applying the load P, find the distance x that locates the position where P must applied so that the bar will remain horizontal. Neglect the weight of the bar AB. L= 3 ft A 0.2 in.? L= 2 ft A = 0.4 in.2 A 10 ft
3. 40 mm- 20 mm 80 mm P Two blocks of rubber, each 80 mm long by 40 mm wide by 20 mm thick, are bonded to a rigid support mount and to a mov- able plate (1). When a force of P = 2,800 N is applied to the assembly, plate (1) deflects 8 mm horizontally. Determine the shear modulus G of the rubber used for the blocks. ans: G=1,15 mPa dy
5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in a horizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is 1000 mm? and E̟ =1×10°N/ mm? . The rod at B is steel, length 5 m , cross-sectional area is 445 mm?. At what distance 'd' from A may a vertical load P=300ON be applied if the bar is to remain horizontal even after the load is applied? ve stred Steel 5m Brass 3m P = 3000N B 9m
The 679-N force is applied to the 114-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.77 = 0.60 Answer: F= i 26° N P = 679 N