Q: 1.)A barrel contains a 0.120 m layer of oil floating on water that is 0.250 m deep. The density of…
A:
Q: A refinery uses a Venturi tube like the one shown in the figure to monitor the flow of gasoline (? =…
A: density of fluid = ρ= 7 x 102 kg/m3 inlet radius = r1= 2.5 cm outlet radius = r2= 1.4 cm pressure…
Q: 3. In a giraffe with its head 2.0 m above its heart, and its heart 2.0 m above its feet, the…
A: distance b/w head and heart is 2 mdistance b/w heart and feet is 2 m.Blood density, ρ=1.06×103…
Q: Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an…
A:
Q: An open tank contains a layer of oil floating on top of a layer of water (density 1000 kg/m^3) that…
A:
Q: How do internal and external cavities affect the buoyant force and the calculated density? is it…
A: Buoyant force = weight of displace liquid
Q: The Venturi tube shown in the figure below may be used as a fluid flowmeter. Suppose the device is…
A: ρ = 711 kg/m3 r1 = 2 cm = 0.02 m r2 = 1 cm = 0.01 m P1 - P2 = 1380 Pa v1 = ?
Q: Equal volumes of two fluids are added to the U-shaped pipe as shown in Figure CQ9.5. The pipe is…
A: In U-tube at point P, the pressured applied by both the liquids is same, hence liquid are…
Q: The container shown is filled with a mystery liquid with density 33.8 ×103 kg/m3. It is open to…
A:
Q: Example # 1: Water enters a house through a pipe with an inside diameter of 2.0 cm at an absolute…
A:
Q: 5 The tube shown in the figure below is called Venturi tube which can be used as a fluid flowmeter.…
A: (a) Using equation of continuity,
Q: What outward force (in N) is needed on the outside of a lung to create the pressure P noted in the…
A: Write the given values of this problem. P=-5.50 mm Hg P=-5.50×133.32P=-733.26 PaA=270 cm2 or 0.027…
Q: Negative pressure or suction is often used to drain body cavities. in the drainage arrangement for…
A: negative pressure supplied to the collection tube = 110 mm hg Density of Hg = 13690 kgm3density of…
Q: How much pressure do you experience when you balance a 0.63 kg basketball on the tip of your finger…
A:
Q: What is the buoyancy force exerted on a cube with sides of length 61.0 cm if the block is fully…
A: Given data: The block is fully submerged in a fluid Side length of cube (s) = 61.0 cm = 0.610 m…
Q: What is the pressure at the bottom of the tank when it is filled with water as shown, in kPa…
A: In this question we have to find the pressure at the bottom of the tank.Please give positive…
Q: When there is no atmospheric pressure, does the pressure doubles when density of the fluid doubles?…
A:
Q: What is the difference between the pressure of the blood in your brain when you stand on your head…
A:
Q: The pressure in the xylem near the base of a tall tree is 1.00 atm. Part 1 What is the pressure in…
A: ...
Q: manometer using oil (density 0.900 g/cm3) as a fluid is connected to an air tank. Suddenly the…
A: The given values are: Density of oil: ρoil=0.9 g/cm3Density of mercury: ρHg=13.6 g/cm3Increase in…
Q: liquid pored into a container fills it to a depth of 11.0ft. If the pressure at the bottom of the…
A:
Q: 1. Which of the following describes an ideal fluid? a. One which obeys Newton's law of viscosity b.…
A: according to bartleby guidelines ,i supposed to answer one question at a time . given:-1)…
Q: 1. As shown in the figure, a large open tank contains a layer of oil (density 450 kg/m³) floating on…
A: Given:water density, ρw = 1000 kg/m3thickness of water, hw = 3.0 mdensity of oil, ρoil = 450…
Q: 4.) What is the total pressure experienced by a diver in a swimming pool at a depth of 2 meters ?…
A:
Q: Both a gage and a manometer are attached to a gas tank to measure its pressure as shown in figure…
A: Given: The gauge pressure is P=50 KPa. The density of mercury is ρ=13600 kg/m3. The expression…
Q: 2. Lake Pinatubo is the deepest lake in the Philippines. Find the pressure at a depth of 10 m below…
A:
Q: A hypodermic syringe contains a medicine with the density of water (1000 kg/m3). The barrel of the…
A:
Q: An ideal fluid, of density 0.90 x 103 kg/m3, flows at 6.0m/s through a level pipe with radius of…
A:
Q: A horizontal pipe of 10 cm in diameter is connected to a pipe of 5 cm in diameter. Suppose the…
A: The diameter of the large pipe is d1=10 cm=10×10-2 m The pressure in the large pipe is p1=8×104 Pa…
Q: A hypodermic syringe contains a medicine with the density of water (1000 kg/m3). The barrel of the…
A:
Q: In medical work, pressures are often measured in units of mm of H2O because body fluids, including…
A:
Q: Compute for the surface tension of a force of 3.65 x 10⁷ dyne acting on 7 m². Determine all in the…
A: In this question we have to compute for the surface tension of a force of 3.65 x 10⁷ dyne acting on…
Q: Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an…
A:
Q: A hypodermic syringe contains a medicine with the density of water. The barrel of the syringe has a…
A:
Q: hypodermic syringe contains a medicine with the density of water (1000 kg/m3). The barrel of the…
A:
Q: The gravitational force exerted on a solid object is 5.20 N as measured when the object is suspended…
A:
Q: 1. The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer…
A:
Q: a) A regular basketball (diameter: 34.2 cm) is entirely submerged in water. Calculate the buoyant…
A:
Q: For what type of situations can you use the Hagen-Poiseuille equation? A) In very narrow pipes…
A: Introduction: Hagen-Poiseuille equation is an equation that gives pressure drop in an incompressible…
Q: When there is no atmospheric pressure, the pressure doubles when thr density of the fluid doubles.…
A:
Q: 1.)A barrel contains a 0.120 m layer of oil floating on water that is 0.250 m deep. The density of…
A:
Q: 1. Llyn Cau in Snowdonia, Wales, is a 35.0-m deep glacial lake popular among outdoor swimmers. (a)…
A:
Q: A manometer using oil (density 0.900 g/cm3) as a fluid is connected to an air tank. Suddenly the…
A: Density of oil = 0.900g/cm3 = 900kg/m3 Density of mercury = 13.6g/cm3 = 13600 kg/m3 Change in…
Q: A barrel contains a 0.150 m layer of oil of density 660 kg/m^3 floating on water that is 0.300 m…
A:
Q: 19) A submarine dives to a depth of 52.5 meters in deep lake. (water density = 1030 kg/m3). What is…
A: Pressure at depth h in fluid of density ρ is, P=ρgh Here, g is acceleration due to gravity. Given…
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- If the pressure in the esophagus is -2.00 mm Hg while that in the stomach is +20.0 mm Hg, to what height could stomach fluid rise in the esophagus, assuming a density of 1.10 g/mL? (This movement will not occur if the muscle closing the lower end of the esophagus is working properly.)The human brain and spinal cord are immersed in the cerebrospinal fluid. The fluid is normally continuous between the cranial and spinal cavities and exerts a pressure of 100 to 200 mm of H2O above the prevailing atmospheric pressure. In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height lo which the fluid rises is observed, as shown in Figure P9.83. If the fluid ruses to a height of 160. mm, we write its gauge pressure as 160. mm H2O. (a) Express this pressure in pascals, in atmospheres, and in millimeters of mercury. (b) Sometimes it is necessary to determine whether an accident victim has suffered a crushed vertebra that is blocking the flow of cerebrospinal fluid in the spinal column. In other cases, a physician may suspect that a tumor or other growth is blocking the spinal column and inhibiting the flow of cerebrospinal fluid. Such conditions ran be investigated by means of the Queckensted test. In this procedure, the veins in the patients neck are compressed lo make the blood pressure rise in the brain. The increase in pressure in the blood vessels is transmitted to the cerebrospinal fluid. What should be the normal effect on the height of the fluid in the spinal tap? (c) Suppose compressing the veins had no effect on the level of the fluid. What might account for this phenomenon?Figure P15.52 shows a Venturi meter, which may be used to measure the speed of a fluid. It consists of a Venturi tube through which the fluid moves and a manometer used to measure the pressure difference between regions 1 and 2. The fluid of density tube moves from left to right in the Venturi tube. Its speed in region 1 is v1, and its speed in region 2 is v2. The necks cross-sectional area is A2, and the cross-sectional area of the rest of the tube is A1. The manometer contains a fluid of density mano. a. Do you expect the fluid to be higher on the left side or the right side of the manometer? b. The speed v2 of the fluid in the neck comes from measuring the difference between the heights (yR yL) of the fluid on the two sides of manometer. Derive an expression for v2 in terms of (yR yL), A1, A2, tube, and mano. FIGURE P15.52
- Pressure in the spinal fluid is measured as shown in Figure 11.43. If the pressure in the spinal fluid is 10.0 mm Hg: (a) What is the reading of the water manometer in cm water? (b) What is the reading if the person sits up, placing the top of the fluid 60 cm above the tap? The fluid density is 1.05 g/mL. Figure 11.43 A water manometer used to measure pressure in the spinal fluid. The height of the fluid in the manometer is measured relative to the spinal column, and the manometer is open to the atmosphere. The measured pressure will be considerably greater if the person sits up.The human brain and spinal cord are immersed in the cerebrospinal fluid. The fluid is normally continuous between the cranial and spinal cavities and exerts a pressure of 100 to 200 mm of H2O above the prevailing atmospheric pressure. In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height lo which the fluid rises is observed, as shown in Figure P9.83. If the fluid ruses to a height of 160. mm, we write its gauge pressure as 160. mm H2O. (a) Express this pressure in pascals, in atmospheres, and in millimeters of mercury. (b) Sometimes it is necessary to determine whether an accident victim has suffered a crushed vertebra that is blocking the flow of cerebrospinal fluid in the spinal column. In other cases, a physician may suspect that a tumor or other growth is blocking the spinal column and inhibiting the flow of cerebrospinal fluid. Such conditions ran be investigated by means of the Queckensted test. In this procedure, the veins in the patients neck are compressed lo make the blood pressure rise in the brain. The increase in pressure in the blood vessels is transmitted to the cerebrospinal fluid. What should be the normal effect on the height of the fluid in the spinal tap? (c) Suppose compressing the veins had no effect on the level of the fluid. What might account for this phenomenon?The water supply of a building is fed through a main pipe 6.00 cm in diameter. A 2.00-cm-diameter faucet tap, located 2.00 m above the main pipe, is observed to fill a 25.0-L container in 30.0 s. (a) What is the speed at which the water leaves the faucet? (b) What is the gauge pressure in the 6-cm main pipe? Assume the faucet is the only leak in the building.
- What is the greatest average speed of blood flow at 37° C in an artery of radius 2.00 mm if the flow is to remain laminar? What is the corresponding flow rate? Take the density of blood to be 1025 kg/m3.How tall must a water-filled manometer be to measure blood pressures as high as 300 mm Hg?The human brain and spinal cord are immersed in the cerebrospinal fluid. The fluid is normally continuous between the cranial and spinal cavities and exerts a pressure of 100 to 200 mm of H2O above the prevailing atmospheric pressure. In medical work, pressures are often measured in units of millimeters of H2O because body fluids, including the cerebrospinal fluid, typically have the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap as illustrated in Figure P14.8. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed. If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. (a) Express this pressure in pascals, in atmospheres, and in millimeters of mercury. (b) Some conditions that block or inhibit the flow of cerebrospinal fluid can be investigated by means of Queckenstedts test. In this procedure, the veins in the patients neck are compressed to make the blood pressure rise in the brain, which in turn should be transmitted to the cerebrospinal fluid. Explain how the level of fluid in the spinal tap can be used as a diagnostic tool for the condition of the patients spine. Figure P14.8
- Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.400 m2, and the pipe gradually widens so that its area near the ground is 0.800 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?A table-tennis ball has a diameter of 3.80 cm and average density of 0.084 0 g/cm3. What force is required to hold it completely submerged under water?Review. In a water pistol, a piston drives water through a large tube of area A1 into a smaller tube of area A2 as shown in Figure P14.46. The radius of the large tube is 1.00 cm and that of the small tube is 1.00 mm. The smaller tube is 3.00 cm above the larger tube. (a) If the pistol is fired horizontally at a height of 1.50 m, determine the time interval required for the water to travel from the nozzle to the ground. Neglect air resistance and assume atmospheric pressure is 1.00 atm. (b) If the desired range of the stream is 8.00 m, with what speed v2 must the stream leave the nozzle? (c) At what speed v1 must the plunger be moved to achieve the desired range? (d) What is the pressure at the nozzle? (e) Find the pressure needed in the larger tube. (f) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.) Figure P14.46