2. Another cylindrical component is madeof Enfennering ceramic Al203but with differentdimensions. Here, l=30 cm and the diameter is 4 cm. Assume the same Weibull modulus of 9.Calculate the level of the tensile strength for the following probability of failures:a. Pr (V) = 0.1b. Pr (Vo) = 0.01c. What is the survival probability and the failure probability of this component if a stress of200 MPa is applied?

To given that,Pf(v)=0.1Pf(v0)=0.01module,m=9a we know that , P=1-e-(σσ0)m…

Answered: dimensions. Here, l=30 cm and the…

dimensions. Here, l=30 cm and the diameter is 4 cm. A Calculate the level of the tensile strength for the follow a. Pr (V) = 0,!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a large plate, the geometry factor, f, is 1.03. Suppose a steel casting alloy has a critical fracture toughness of 78,886 psi*in1/2. The steel will be exposed to a stress of 40,295 psi during service. Calculate the minimum size of an edge crack that will grow. Repeat the calculation for Al2O3 with a fracture toughness of 1,600 psi*in1/2. How many times larger is the minimum size edge crack in the steel versus the alumina?
A fatigue test was conducted in which the mean stress was 70 MPa and the stress amplitude was 210 MPa. Compute the following (a) The maximum and minimum stress levels. (b) Strss ratio, (c) Stress range
Determine the strength of the bedrock granite. Assume you sampled the granite where it was exposed at the surface and ran a series of 4 triaxial compression tests (results given below). Determine the Coloumb coefficient (or friction angle) and the cohesion of the rock given these test results. Either use graph paper to draw Mohr’s circles and a failure envelope to help you determine these values or use the computer to make a plot. Show all your work for credit! Test Confining pressure Axial load at failure 1 4.5 MPa 35.5 MPa 2 9 MPa 50 MPa 3 17 MPa 73 MPa…
Compression springs are the most common spring configuration that product manufacturer's turn to when enhanced product functionality is required. You are required to design a compression spring that is made of oil-tempered wire of 4-mm diameter with a spring index of C=10. The spring will operate inside a pipe, so buckling is not a problem and select the ends to be plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. a) Calculate the spring rate and the solid length. b) Calculate the total number of coils needed. c) Calculate the minimum pipe diameter for the spring to operate in. d) Calculate a static factor of safety based on the yielding of the spring if it is compressed to its solid length.
Using the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.
Figure 5 shows a failure assessment diagram (FAD) from the R6 calculator spreadsheet. (a) Make a copy sketch of the FAD in Figure 5, and indicate the regions of brittle fracture and plastic collapse. (2 mark (b) Using Figure 5, calculate the reserve factor on load. Explain how you obtained your answer. (4 mark. (c) Indicate on your sketch the effect on the FAD if: (i) a residual stress were present in the vicinity of the crack (ii) the crack length were increased (iii) the toughness of the material were improved. (3 + 3 + 3 = 9 marks Plate in tension - through-thickness edge crack 1.2 08- 0 76. 0 81 *06- 20 46. 0 48 04- 02- 0O 02 04 0.6 0.8 10 1.2 1.4 1.6 L, Figure 5 FAD for Question 6
The table below shows the deformation data that resulted from applying a pure tensile load to a brass alloy rod with an initial length of 30 mm and a diameter of 10 mm. This rod was subjected to necking and beyond necking deformation. The data at fracture is shown in the last row. Applied Load (N) Length (mm) Diameter (mm) 75,100 33.8 68, 250 34.9 50,200 35.7 6.7 Solve for the TRUE STRESS/ES and TRUE STRAINS. 8.3 7.8
A fatigue test was conducted in which the mean stress was 90 MPa (13050 psi), and the stress amplitude was 200 MPa (29010 psi). (a) Compute the maximum stress level. MPa (b) Compute the minimum stress level. MPa (c) Compute the stress ratio. (d) Compute the magnitude of the stress range. MPa
1) Draw (using a normal graph paper) a conventional stress-strain diagram for ANY metallic material (e.g. steel, aluminium, copper, brass, iron, tungsten). The diagram should be as accurate as possible using a suitable scale (e.g. 1cm: 10 N). 2) Calculate the Modulus of Elasticity, Modulus of Toughness and Modulus of Resilience for the material from the stress-strain diagram. Show your calculations in detail on a separate A4 piece of paper.
(a)Describe, with a labelled diagram, how you would measure accurately theextension of such a wire under an applied load. (b) The graph below shows how the extension of a wire varies with the loadapplied to it. The wire used has a length of 3m and a diameter of 5 x 10^-4m i. Calculate the tensile stress produced by a load of 50N.ii. Find the energy stored in the wire when the load is acting.iii. Calculate the reduction in gravitational PE of a 5kg mass used to providethe load.iv. Calculate Young's modulus for the metal of the wire.
a)Draw the stress-strain curve of a ductile material such as that of a ductile steel and discuss the various regions of the curve. Explain the difference between a ductile and brittle material and the concept of ductility and its measurement. b)A machine part 10 mm thick, having the dimensions shown in the figure, is to be subjected to cyclic loading. If the maximum stress is limited to 60 MPa, determine the allowable force P. Approximate the stress concentration factors form the graph given. Where might a potential fracture occur?
Project 2: Table 3 & 4 shows the fatigue data for two different materials to be used for an automobile rotating parts at an average rotational speed of 750 revolutions per minute: Stress in Mpa 170 148 130 114 92 80 74 Table 3: Summary of fatigue data part 1 Number of cycles 37000 100000 300000 1000000 10000000 100000000 1000000000