1) Draw (using a normal graph paper) a conventional stress-strain diagram for ANY metallic material (e.g. steel, aluminium, copper, brass, iron, tungsten). The diagram should be as accurate as possible using a suitable scale (e.g. 1cm: 10 N). 2) Calculate the Modulus of Elasticity, Modulus of Toughness and Modulus of Resilience for the material from the stress-strain diagram. Show your calculations in detail on a separate A4 piece of paper.

1) Draw (using a normal graph paper) a conventional stress-strain diagram for ANY metallic material (e.g. steel, aluminium, copper, brass, iron, tungsten). The diagram should be as accurate as possible using a suitable scale (e.g. 1cm: 10 N). 2) Calculate the Modulus of Elasticity, Modulus of Toughness and Modulus of Resilience for the material from the stress-strain diagram. Show your calculations in detail on a separate A4 piece of paper.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 2 shows the stress versus strain curve of four engineering materials. Compare the ability of the materials to sustain stress without fracture and their ability to absorb the energy before fracture between Material A and D. A C В D Strain Figure 2. Stress versus strain curve of four engineering materials. Stress (MPa)
Given a example of copper specimen that has had a tensile test conducted on it. Diameter of 6.4mm Max force of 11112.5N Max extension of 7.79mm Calculate: 1) modulus of elasticity 2) tensile strength 3) the ductility, in percent elongation 4) yield strength at a strain of 0.002
Which of these cracks will lead to failure first from the table in the picture? And present your findings in a table format and comment briefly.
Need correctly in proper handwriting
The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
Pls help ASAP on this question. Pls do all of them. Just need one sentence for each question.
I cylindrical piece of an unknown material 5/8" in diameter is subjected to a longitudinal tension load. Under a load of 1,650 lbs you measure a strain of 0.0005". Assume that this stress is within the elastic range of the material. Calculate the modulus of elasticity. Modulus of elasticity |(include units)
Only Handwritten please. ( NO typed)
Poisson's ratio is defined as (a) longitudinal strain/lateral strain (b) lateral strain/longitudinal strain (c) lateral strain x longitudinal strain 1 (d) (lateral strain) x (longitudinal strain) -
Can you please answer question B, thank you
2
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience