Determine the x- and y-coordinates of the centroid of the shaded area. Assume c = 7, a = 1.25, b = 2.30, x and y are in inches.     (0.98, 1.84)     (1.98, 0.84)     (1.84, 0.98)     (0.84, 1.98)

Q: A rigid, perfectly insulated system contains 0.53m3 of helium at 1000 kPa. The system receives 1000…

A: Since the container is rigid, the volume of the helium remains the same. Also, the adiabatic index…

Q: Nitrogen in a rigid vessel is cooled by rejecting 100 kJ/kg of heat. Determine the internal energy…

A: Given data : Heat loss from a rigid vessel, Qloss = - 100 kJ/kg In case of rigid vessel, change in…

Q: Based on the figure below. Find the force on P in newton that will produce a resultant force of 390…

A:

Q: A suspended date that's able to pivot from the top seperates two liquids. There is a stopper that…

A: Given, Gate height, h=0.5 m Since, the liquid on the right is twice as dense as liquid on the left.…

Q: w[N/m] wohn(x) 8m Find the location of the application of the resultant force to genovare the…

A:

Q: 4.67 Determine the reactions at B and D when b = 60 mm. hp 80 N A D 75 mm 250 mm 90 mm- B

A:

Q: How do you know that Fa=568N?

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Moment of a Force-Vector Formulation Learning Goal: To use the vector cross product to calculate the…

A:

Q: 2) it is observed that the frequency of oscillation of a y guitar string of depends upon the Mass…

A:

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

A:

Q: 2. In an Ideal Rankine Cycle, the steam throttle condition is 8Mpa and 480C. If turbine exhaust is…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: 1. A 10-cm-diameter siphon tube is used to empty the reservoir and discharge it into the air (Figure…

A:

Q: A dairy farm needs to chill the milk from 39°C (extraction temperature is the same as the cow's body…

A:

Q: The mass center G of the 1235-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: A spring-loaded piston-cylinder device contains 0.21 kg of water initially at 90°C and with an…

A:

Q: Exercises 1. The approach & efficiency of cooling tower is 10°C 4 60% respectively. If the tempe.…

A:

Q: Determine the stresses in members LM, HM and CH. L x M N 0 P A H 40 k B 40 k C D 40 k 6 at 30 ft 180…

A:

Q: 1. Please solve dy/dx=y/x +sin (y/x) 2. Xdy/dx+y²/x=y Solve both

A:

Q: The 380-kg uniform I-beam supports the load shown. Determine the reactions at the supports.

A:

Q: Steam enters a turbine operating at steady state at 850°F and 450 lbf/in² and leaves as a saturated…

A:

Q: An industrial plant has available a 4 cylinder, 3 in bove by an, stroke, 800 rpm, single-acting…

A:

Q: Give the Following: Page 1 - Explanation of table (formula of Speed of sound for metric system) Page…

A: The altitude data in meters is as shown below. height(ft) height(m) sea level sea level 1050…

Q: 2. In an air conditioning system, if the recirculated air is three times the outside air and the…

A: Given : mass of supply air. ms = 20 kg/s mass of recirculating air = 3 * mass of the outside air To…

Q: The man unes the hand truck to move material up the step The truck and contents have a mass of 40 kg…

A:

Q: Refrigerant 134a enters an insulated diffuser as a saturated vapor at 80°F with a velocity of 800…

A: Given Referigerent-R134aT1=80oFV1=800ft/s=800×0.3048=243.84 m/sA=1.4 in2=1.4×0.02542=9.03224×10-4…

Q: Define heat of combustion

A: combustion: Combustion is the process of burning of any fuel in the presence of air. The air may be…

Q: Given the applied load and properties of a simply supported I-beam, determine the initial…

A: Given Data

Q: Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact…

A: subject : engineering drawing

Q: A closed, rigid tank contains 1.50 kg of water, initially a two phase liquid-vapor mixture at T₁ =…

A: Given data :- mass = 1.50 kg Initial T1=90°C (saturated mixture) And final T2 = 120°C (saturated…

Q: An existing turbine has the following data: D = 95 cm, H = 27 m, Q = 69.9 m3/s, ρ = 998 kg/m3, N =…

A:

Q: On a windy day, a camper feels colder as compared to a day at the same temperature when there is no…

A: given=On a windy day, a camper feels colder as compared to a day at the same temperature when there…

Q: 50 kN.M 10 kN ↑ mt 5m 10M 10m 20 kN 10 kN 5ml 5m. 100 kN.m

A: We can answer up to 3 sub parts ( here 3 images) so we will answer for first 3 of the left side…

Q: Find the absolute pressure (kPa) at a depth of 5m below the surface of a liquid with relative…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: The 380-kg uniform I-beam supports the load shown. Determine the reactions at the supports.

A:

Q: A Determine the reactions at A and B for the given simply supported beam. 200 lb Ift 100 lb ft ·5ft-…

A:

Q: If the 45 degree offset distance at point B is 8 inches, the "travel" distance (center to center)…

A: It is given that the offset is 45 degrees and it is needed to determine the center to center…

Q: 2. With the aid of suitable sketch diagram(s), explain the working principle of air-water HVAC…

A: HVAC system: HVAC is described as heating ventilation and air conditioning system. So it consist of…

Q: 4. The gain in entropy during an isothermal non-flow process of 5 lb of air at 60°F is 0.462 Btu/R.…

A:

Q: If gear A rotates with a constant angular acceleration of aA = 89 rad/s2, starting from rest,…

A: Introduction If two or more gears are installed on the same shaft in a compound gear configuration,…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A:

Q: A turbine has the following data:  inlet radius = 2.2 m    outlet radius = 1.5 m     blade width at…

A: Given Data: Inlet Radius R1=2.2 m Outer Radius R2=1.5 m Width of the blade at the inlet w1=0.8 m…

Q: A coupling joins two shafts of 15 mm diameter (D = 15), transmitting torque T that varies f 100 to…

A: This is question related to the coupling joints. Coupling joints connect two rotating shafts and…

Q: A butt joint with a single strap connects two axially loaded structural members as shown below.…

A:

Q: Determine the amount of energy (kJ) that needs to be transferred to the water to raise its…

A: Given:-Mass of water (m) = 55 gallons As 1 gal = 3.79 kg of waterhence Mass of water (m) =…

Q: At a given instant the top B of the ladder has an acceleration aB = 2.0 ft/s2 and a velocity of vB =…

A:

Q: The power output of an adiabatic steam turbine is 5MW and inlet and the exit conditions of the steam…

A:

Q: Determine the z-coordinate of the centroid of the volume obtained by revolving the shaded triangular…

A:

Q: Calculate the fan power (in kW) if the average pressure drop is 6 In. H2O. Assume the fan Is 70%…

A: Given-Information:- Q = 20000 ft/m3T1 = 77°FP1 = 1 atm To-Determine:- Fan power

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.