Determine the stresses in steel and concrete of the concrete section shown. Assume N32 concrete & 6N20 steel bars used to resist tension as shown. Assume Mas 140kNm. Take the shrinkage strain as 450micron. Comment on the compliance of Cl.8.6.2.2 of AS3600 60 (2018). (HOMEWORK) 350 b=320 D

Q: ation 9: Three rods, each of area 250 mm2, jointly support a 7.5 KN load, as shown in Figure.…

A:

Q: Test No Temperature C Deformation rate(mm/min) Strain at break Youngs modulus (Gpa) Stress at…

A: Step 1: UTS mean Ultimate tensile strength. From the conventional stress strain curve, it is…

Q: O AF F. p0.2 p0.2 p0.2 S. 0.2-mm (0.2% of 100 mm=0.2-mm)- AL II R.

A:

Q: Three proposed cross-section configurations for joining three boards are shown in Figure 1. Each…

A: Given, b = 50 + 29 + 9 = 88 mm  Mz = 5000 Nm or 5 x 106 N-mm

Q: P- 3P 2P Steel Bronze Al A = 200 mm A = 400 mm A = 500 mm = 150MPA e= 100MPA c = 80MPA

A:

Q: 28 MPa. (A#25 = 510mm^2) 420 mm 500 mm 2 #25 80 mm - 300 mm

A:

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

A:

Q: *3-20. The stress-strain diagram for a bone is shown and can be described by the equation € = 0.45…

A:

Q: The cross section of a beam constructed using Grade 50 concrete (Ec = 34800 MPa) is 300 mm x 500 mm…

A:

Q: A cube of a material with a yield strength of 100x10° N/m?is subjectedtothe loads shown onthe right.…

A: The maximum shear stress is generally the maximum concentrated shear force in a small area. In…

Q: The properties of the reinforced concrete beam are b = 309 mm, d = 476 mm, Ast = 1376 mm2, and Est /…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: To Find :- flexural stress at bottom fiber Given data:- a = 50 mm, b= 110 mm, c= 70 mm E = 140 GPa =…

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

A:

Q: 4N20 450 mm 390 mm 300 mm

A:

Q: Question alt A (200 x 100 x 50) mm³ steel block is subjected to a hydrostatic pressure of 15 MPa.…

A: Given- Size of block- 200×100×50 mm3 Poisson's ratio μ=0.3 Young's modulus E=200 GPa, Hydrostatic…

Q: Strength of Materials II HOME WORK 1- Bending For the composite beam shown in the figure below,…

A: Given:- A composite beam of steel and aluminum is given  The magnitude of the uniformly distributed…

Q: Three rods, cach of area 250 mm2. jointly support a 7.5 kN load, as shown in Figure below. Find the…

A: My dear  Given data Total hanging load Two types of materials. Area of cross section  Youngs modulus…

Q: Choose the correct answer Rate of strain has units:        b. m2       e. m/s2       d. m/s…

A: The strain is the deformation due to the applied load, it is a measure of the change in shape and…

Q: A 220 mm? steel rod and 420 mm? copper rod supports a rigid bar as shown. If a 30 kN load is…

A:

Q: A flat bar of cross section 15 mm by 70 mm elongates 2.59 mm in a length of 1.3 m as the result of…

A: Axial stress is the ratio of load and the areaσ=PAσ=230,000N15×70 mm2σ=219Mpa

Q: a concrete beam simply supported at both ends 300 × 600mm it stressed by 3 cables of 700 mm each…

A: given data: ps =1200n/mm2                     e=100mm, ec =30,000

Q: given material has a modulus of elasticity E=250 GPa and shear modulus G= 83.5 GPa, what is the…

A:

Q: Show that the strain rate of a wire stretching through a die can be expressed by e=2tg(a)/r *(dx…

A: The strain rate is given by e=2tanαr.dxdtwhere,α is die angler is radius of wiredxdt is rate of…

Q: Q.3 (b) A uniform cantilevered steel column with one end fixed and one end free in both directions…

A:

Q: 4. Consider a unit cube of a solid occupying the region 0 ≤ x ≤ 1,0 ≤ y ≤ 1,0 ≤z ≤ 1, After loads…

A:

Q: to a bending moment M = Last four digits of your registration number in N-m. Analyse the curved beam…

A: To find all parts

Q: A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner…

A: Given: Length of rod, L = 1 m = 1000 mm Outside diameter of rod, Do = 0.2 m = 200 mm Inner diameter…

Q: Help me with Solution, Need fast. Do not waste time. A steel beam is installed in a building when…

A:

Q: Problem 11.9 The cube of material shown in Problem 11.8 (reproduced below) is subjected to a pure…

A:

Q: Determine the ductility of a tested material in terms of percent elongation and percent reduction…

A:

Q: Osa 18° Taa /a 45° a 200 MPa 50 MPa

A: GIVEN:  TO DETERMINE: The Normal stress on plane a-a  CONCEPT: Angle substended by two planes on…

Q: o (MPa) B 100 95 compression 70 80 2 m 60 50 tension 40 32.2 20 C 0.75 m '0.75 m 0.5m E (mm/mm) 0.01…

A:

Q: E al = 70Gpa  E cu = 75 Gpa  fınd the max stress in both of tow materials in the picture

A: The composite structure is construct of more than one material this will increase the strength and…

Q: The elastic portion of the force-extension diagram for a specimen under uniaxial loading is shown in…

A:

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.