Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV j0.150 2 MVA 22/6.6 kV 1 MVA 6.6 kV/400V Z=3% 25 MVA fault level 6.6 kV switchboard 400 V switchboard

Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV j0.150 2 MVA 22/6.6 kV 1 MVA 6.6 kV/400V Z=3% 25 MVA fault level 6.6 kV switchboard 400 V switchboard

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.10P: A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding...

See similar textbooks

Similar questions

A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
A generator supplies a motor through a Y-A transformer. The generator is connected to Y side of the transformer. A fault occurs between the motor terminals and the transformer. The symmetrical components of the subtransient current in the motor flowing toward the fault are: I =-0.8- j2.6pu I =-j2.0pu I =-j3pu From the transformer toward the Fault: I = 0.8– j0.4pu I? =-j1.0pu 1 = Opu Assume X =X,=X, for both the motor and the generator. (a) Describe the fault type and find the prefault current, if any, in line a. (b) Determine the subtransient fault current in per unit. (c) Calculate the subtransient current in each phase of the generator in per unit taking into consideration the phase shift of the Y-A transformer.
In the single-phase, three- winding, transformer, the primary current is equal to lo at the condition of ints there is no load on tertiary windings the current in secondary windings equal to zero the resistances (R1, R2, and R3) in transformer windings are equal the inductances (L1, L2, and L3) in transformer windings are equal.
A 12 MVA, 132/6.6 kV, transformer having a reactance of 0.15 pu is fed from an infinite bus. The transformer feeds two motor each 6 MVA, 6.6 kV. Each motors has a transient reactance of 0.14 pu and a subtransient reactance of 0.30 pu based on its own rating. A three phase balanced fault occurs at the terminals of one motor as shown in the figure below. Find the subtransient fault current and subtransient current in breaker. M1) 132/6.6 KV СВ 38 CB Infinite Bus M2 Fault
3. Single-phase T1-transformer with a power of 500 kVA and a single-phase T2- with a power of 400 kVAtransformers are connected in parallel and load 1000 kVA with 0.8-back power factor.they are feeding. The equivalent circuit winding resistance of T1 is 0.025 b and the equivalent circuit reactance is 0.06is b. The equivalent winding resistance of T2 is 0.016 b and the equivalent circuit reactance is 0.07 b. Bothhas the same conversion ratio in the transformer.a. Draw the connection diagram given in the question. b. Obtain the power sharing expression over the parameters given in the question. c. Calculate the kVA values and power factors of the transformers.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.
A A-A three transformer bank, each of 10 kVA supply a total load of 20 kVA. One of the transformer become, disable and hence the circuit works on V-V open delta connection. Find for this connection. (a) (b) (c) (d) (e) kVA load carried by each transformer. % of rated load carried by each transformer. Total kVA rating of V-V open A connection. Ratio of V-V and closed A ratings. % increase in load on each of the two V-V connected transformers. M
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
In no load phasor diagram of practical transformer, the magnetizing current Imag is with flux Ø O Leading by 30° O Lagging by 60° In phase O 90° out of phase
Tutorial 1.7 The three-phase ratings of a three-winding transformer are: Primary Y-connected, 66 kV, 24 MVA Y-connected, 13.2 kV, 12 MVA Secondary Tertiary A-connected, 2.3 kV, 4 MVA Neglecting resistance, the leakage impedances are: Zps Zns = 6% on 24 MVA, 66 kV base Zpt = 8% on 24 MVA, 66 kV base Zst = 7% on 12 MVA, 13.2 kV base Find the per-unit impedances of the per-phase equivalent circuit for a base of 24 MVA, 66 kV in the primary circuit. {Ans: j 0.0; j 0.06; j 0.08}
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer