Determine the resultant of the force system shown in Fig. P-263 & its x& y intercepts.0007"Y300lb361 lbR = 161.318 lb, ix = 1.67 ft right of 0, iy = 0.67 ft below OR = 161.318 lb, ix = 1.67 ft left of 0, y = 0.67 ft above 0R=163.118 lb, ix = 0.67 ft right of O, iy = 1.67 ft below OR=163.118 lb, ix = 0.67 ft left of 0, y = 1.67 ft above 0X224 lb

Answered: Image /qna-images/answer/7694c788-f541-475b-9a36-fdeb2daf4771.jpg

Answered: Determine the resultant of the force…

Engineering

Civil Engineering

Determine the resultant of the force system shown & y intercepts. Y 300)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular concrete beam 120 x 300 mm is prestressed by straight cable, effective force 180 kN at…

Q: A soil element is loaded from state A to B. The stress values for the two states are A(p'=50 kPa,…

A: Given: Stress values at state A and B Volumetric strain increment=?

Q: The depth of water below the spillway and after hydraulic jump are 1 m and 6 m respectively. The…

Q: 1. A steel column has an unsupported height of 5.4 m is pin connected at both ends with sidesway is…

A: L= 5.4 m P=530 kN Top Mx= 20 kN-m My= 3 kN-m Bottom Mx= 13.5 kN-m My= 1 kN-m Fy =250 kN To check -…

Q: -80mm ↓P=240KN 0.6m P E=70 GP₂ ✓=0.3 800 KN 2 - A circular tube is loaded in compression, as shown…

Q: 3. A pump which has at total head and power of 40 m and 37 kW is operating at a rate of 5670 L/min.…

A: To calculate the performance of the pump at 1250 rpm, we will need to use the affinity laws for…

Q: 4 - A rubber material is attached between two rigid plates. If the lower plate is held in place,…

Q: Isosceles traingle gate AB is hinged at A and weights (155 kg) What horizontal force P is required…

Q: column of size 450 mm x 600 mm has unsupported length of 3m and is braced against side sway in both…

Q: The concrete floor of a hand regulator is level with the channel bed and is 13 m long. The depth of…

Q: Problem 1 The void ratio versus pressure data shown below. The initial void ratio is 0.725, and the…

A: A table is given of void ratio and pressure and it has been asked in the question to evaluate Plot…

Q: The pinned joint shown here is held by a 1-cm-diameter pin. The thickness of the two members are t₁…

A: Given, Pin diameter (d) = 1 cm or 10 mm Thickness of plate 1, t1 = 0.5 cm or 5 mm Thickness of plate…

Q: The relative velocity is defined so that VA/B-VA-VB-A graphical version of this equatio 0 Answer: 0-…

Q: A зоки/т Чт ще

Q: a. The reactions at A and B for the "weightless" beam shown in the figure. b. The internal…

A: Given: Required : Support reactions Internal forces and moments at 1 m away from a and b

Q: A beam with a W360x45 section (Beam weight 45 kg) is used as a cantilever beam 7.5 m long. Find the…

Q: A gravity dam has an upstream water depth of 75 m and tail water depth 7m as shown in the figure. To…

A: Given data- A gravity dam- Upstream water depth H=75 m, Tail water depth h=7 m, To Find- The value…

Q: Three reservoir are connected as shown in figure 1. What is the discharge in each line? All pipes…

A: The given figure is shown below:

Q: 2. In general order of importance, the senses most used by drivers are (eyes) 8. For a driver in a…

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

Q: Select the lightest ASTM A992 W-shape column to carry an axial dead load of 200 kips and a live load…

Q: Situation 4: Given the truss shown, determine the maximum value of the downward force P if the…

Q: Shear Question Factored shear force of 140 kN is applied on a beam having breadth 250 mm. The beam…

A: Given Data Factored shear force (Vu) = 140 KN Width of beam (b) = 250 mm Factored torsional moment…

Q: Specific energy of flowing water through a rectangular channel of width 5 m when discharge is 10…

A: Given- Width b=5 m Discharge Q=10 m3/s Depth y=2 m, It is needed to find the specific energy.

Q: Calculate the friction drag on a plate 0.15 m wide and 0.45 m long placed longitudinally in a stream…

Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…

Q: Answer the following with (True) or (False): 1- A siphon is a closed conduit designed to run…

A: Reference : Irrigation Engineering Given : 5 statements on weirs and Barrages. To determine : To…

Q: A normal-weight concrete rectangular beam has dimensions b by h with an effective depth of d and is…

A: b=281 mmh=582 mmd=562 mmM=124 kN.mEs=200 GPafy=414.7 MPaf'c=27.6 MPaReinforcement: 3 nos. of 25 mm…

Q: What techniques have been utilized by designers to solve these challenges? What specific sustainable…

A: SOM's Pertamina Energy Tower for Jakarta is the striking centerpiece of the new consolidated…

Q: A rectangular beam with b = 200 mm and effective depth d = 300 mm is subjected to limit state shear…

A: Given- width b=200 mm effective depth d=300 mm limit state shear=80 kN torsional moment = 6 kN-m

Q: A cantilever beam is carrying a 15 kN/m uniformly distributed load over its length of 5 meters.…

Q: Determine the difference between the capitalized cost of the timber and steel penstock for a…

A: Capitalized cost is defined as the present worth of a constant annual cost over an infinite analysis…

Q: a. Compute reaction forces based on "W1". W1=10 kN. b. Compute internal forces/moments at a-a. W1 1m…

Q: A 7.5m cantilever beam shown carries a 115KN/m uniform load. Point A is free end while point B is…

A: Given data in question Length 7.5 m UDL 115 kN/m A is free end To find out Value of EIY at free…

Q: A cast-iron beam carries a uniformly distributed load on a simple span. Compute the flange width "b"…

A: A cast iron beam is given in question and it has been asked to determine b(width of flange)

Q: 9.6. A) Classify the soil with the following properties according to the USCS. % passing Dia (mm)…

A: Given :- % passing with the corresponding Diameter of soil. Liquid limit, LL = 33% Plastic limit ,…

Q: A steel rod is rigidly attached to two walls as shown in the figure. If origin al temperature (T1)…

Q: A rigid bar is supported by two copper ro ds and the gap (A) between the aluminu m rod and the bar…

Q: Write (dynamic viscosity, kinematic Viscosity, Specific gravity, Bulk Modules of Elasticity) in MLT…

Q: The major and minor principal stresses at a point are 3 MPa and -3 MPa respectively. The maximum…

A: Given: The major principal stress, σ1 = 3 MPa The minor principal stress, σ2 = -3 MPa

Q: Check the determinacy of the structures 16) Hinge Hinge Hinge 3.

Q: Water has to be supplied to a town with one lakh population at the rate of 150 litre/capita/day from…

Q: Hinge Check the determinacy of the structures in Fig Hinge

Q: A rigid bar is supported by two copper r ods and the gap (A) between the alumin um rod and the bar…

Q: -19. The piece of plastic is originally rectangular. Determine the shear strain Y., at corners D and…

A: Find: Shear strain at D and C

Q: Given a-4 m and b-10 m, locate the x coordinate of the center of mass of the compound homogeneous…

Q: 1. At 10:00 am the inflow to a reservoir was 20 m³/s and outflow was 12 m³/s. At 10:30 a.m. the…

Q: A rectangular channel of bed width 2 m is to be laid at a bed slope of 1 in 1000. Find the hydraulic…

A: Given Bed width b=2 m Bed slope 1 in 1000 C=50,

Q: 3.8 Following CT scanning, data are available for a chalk core plug from the North Sea area. The…

Q: A post tension beam section drawn below consists of three cables of 100 mm² area. Initial…

A: Given- 3 cables of 100 mm2 area Initial prestressing in cable = 600 N/mm2 modular ratio m=6 It is…

Question

Determine the resultant of the force system shown in Fig. P-263 & its x
& y intercepts.
000
7"
Y
300lb
361 lb
R = 161.318 lb, ix = 1.67 ft right of 0, iy = 0.67 ft below O
R = 161.318 lb, ix = 1.67 ft left of 0, y = 0.67 ft above 0
R=163.118 lb, ix = 0.67 ft right of O, iy = 1.67 ft below O
R=163.118 lb, ix = 0.67 ft left of 0, y = 1.67 ft above 0
X
224 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/ Determine the resultant moment of the force about point C F=400N 100 N D 30 45 0.3 m A 100 N -04m tozm t 0.2 m
In order to replace the loading system acting on the beam shown below by a resultant force and a couple moment acting at Point B: x 4m 19KN FR 8 * * 4m 2m xN/m Determine: a) The component of the resultant force in the x-direction (FRx). Provide the direction of the force. b) The component of the resultant force in the y-direction (FRY). Provide the direction of the force. c) The resultant couple moment (MRB). Provide the direction of rotation (CW or CCW).
Beam ABC is supporting beam CD. Which of the following gives the value of x if reaction at B is 380N Draw the FBD. THU X 600N 10m O x = 1.m O x = 1.50 m O x = 1.75 m O x = 2m O x = 2.50 m B WHIT +4 120N 1m 2m C 300N/m 12m D *
300 mm FN kN SN kN-mm 250 mm MN kN A SN kN FN kN 200 mm FN kN 100 25° mm 150 mm Compute the following in vector form A. The resultant forces [resultant] B. Moment at MN kN force [momenta] ALVIN (FN) = 1 + 12 + 23 + 9 + 14 = 59 NAVALTA (MN) = 14 +1+ 23 +1 + 12 + 21 + 1 = 72 %3D %3D DELIRO (SN) = 4 + 5 + 12 +9 + 19 + 16 = 65
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F E b G B b b C a Q Zoom image Compute the force on member CL P
ying Pl... Q.8 In the design of a control mechanism, it is determined that rod AB transmits a 260 N force P to the crank BC. Determine the x and y components of P. (2) P- 260 N A. 12 y 30
Q2/ Determine the resultant moment of the force about point C F =400N 100 N D 30 A 45° 0.3m B 100 N 0.4m tozm 0.2 m
Determine the resultant of the force system in next fig. Then locate it with respect to point (A). 1000N.m 80 N 10m 150 N 100 N l0m
The cord passing over the two small pegs A and B of the board is subjected to a tension of T = 100 N. The resultant couple moment produced by the two cords is 20 Nm, clockwise. Part A Determine the minimum tension P of the cord passing over pegs C and D. P = 16.35 N T 30° Part B Determine the corresponding orientation angle of the cord passing over pegs C and D. 0 45 A 300 mm D B 30⁰ -T 300 mm
otorm Snie F-A0ON P:450 N Find the magnitude 30° 45 and direction of the 30° resultant of the three forces P, F,Q in the figure Q:700 N
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c = 5m 5 panels@(a)m each F E b B b b P G C Zoom image Compute the force induced in member AB
F224006 F3=60016 f1%=700lb 30° Detremine the magnitude of the resultant force acting on the corbel and its direction 0 measured counterclockwise from the x axis.