Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1539 kJ is supplied to saline water in the steam generator to heat from 21ºC to 104ºC for the generation of water vapor, Take the density & specific heat of the solution as 1022 kg/m3 & 4.8 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg) Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3

Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1539 kJ is supplied to saline water in the steam generator to heat from 21ºC to 104ºC for the generation of water vapor, Take the density & specific heat of the solution as 1022 kg/m3 & 4.8 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg) Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Similar questions

Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
10 kg of saturated liquid water is held in a container at 20 psi Heat is added until the water becomes a saturated vapor, determine the total amount of heat transfer (in kj) required for this to occur if A.) The process orccurs in a riddi tank B.) The preocess occurs in a piston cylinder device
W m-°C. 1.)A 2mx2m aluminum sheet (240 is 5mm thick and used to separate two types of gas (1.1) and (55) in an experimental chamber. The 1st type of gas is maintained at 20℃ while the 2nd gas is at -20C. Solve for the rate of heat transfer in kW.
the specific heat capacity of the system during a certain process is given by Cn(0.4+0.004T) kJ/kg deg. celcius. if the mass of the gas is 6kg and its temperature changes from 25 def. celcius to 125 def. celcius find the mean specific heat of the gas
Q1) The heat capacity at constant volume of hydrogen sulfide at low pressures is given by Eq. Q1-1: Co[kJ/(mol•°C)] = 0.0252 + 1.547 × 10-T – 3.012 × 10-9T² Eq. Q1-1 ........ Where, Tis temperature in °C. A quantity of H2S is kept in a piston-fitted cylinder with initial temperature, pressure, and volume equal to 25°C, 2.0 atm, and 3.0 liters, respectively. i- Calculate the heat (kJ) required to raise the gas temperature from 25°C to 1000°C, if the heating takes place at constant volume (i.e., if the piston does not move). ii- For a closed system at constant pressure with negligible kinetic and potential energy changes, the specific heat is determined by Eq. Q1-2: Cp = Cy + 0 008314 Eq. Q1-2 calculate the heat (J) required to raise the gas from 25°C to 1000°C at constant pressure. What would the piston do during this process? Given the gas constant = 0 08206 atm. Lit/ (mol. K)
5. For a certain ideal gas R - 25.8 ft-lbf/ Ibm-R and k 1.09. Compute the value of the specific heat at constant pressure in Btu/lbm-R.
In a reciprocating air compressor, high pressure air in the cylinder pushes the piston against the external load and expand to a lower pressure. In a test the following measurements were noted:Internal energy of air before expansion = 27 kJInternal energy of air after expansion = 8 kJHeat entering the cylinder during the process = 2 kJSHOW THE DIAGRAM USING THE GIVEN PROVIDED
As shown in the diagram, the state of helium gas is changed in such a way that its PV graph is a straight line segment with volume Vo increases to yVo and pressure Po increases to xPo where x and y are arbitrary constants. During this process the total heat transferred to the gas is equal to the heat necessary to double the absolute temperature of the gas at constant volume. What is the maximum ratio for the volume increase? xP, P. Vo
In the air conditioning process in the humidifier, air at a dry bulb temperature of 30 degrees C and RH of 10% increases its RH to 50%. Determine the amount of moisture added in the humidifier per kg of dry air: ....
Heat that is added to, or subtracted from, a substance that changes its temperature but not in physical state is called (a). COP is defined as (b). Which Gas law defind as the volume of a ideal gas remains constant (). Thermometer is used to meaure the temperature of moist air is called (d). hp
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. a)Find the temperature at the moment the pin breaks. b)Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
B2. The heat energy of 1605 kJ is supplied to saltwater in the steam generator to heat from 25°C to 104°C for the generation of water vapor, Take the density & specific heat of the solution as 1028 kg/m³ & 3 J/kg°K respectively. Determine the quantity of saltwater in the steam generator. I Solution: i) Change in Temperature (in K) ii) Mass of the saltwater (in kg) iii) Quantity (Volume) of salt water (in m³)