Determine the nominal tensile strength based on the effective area (Ae). I am aware that the equation for Ae= Ag*U Determine the nominal tensile strength bused un theeffective crenCAe)2L5x3xリ4 LLB3(twoangles, long legsback-fo-buctk)A242 SteelPL7/8" diameter bolts3:4

Given Data: The two angle connected back-to-back are L 5x3x1/4 The diameter of the bolts is db=7/8…

Answered: Determine the nominal tensile strength…

Determine the nominal tensile strength bused un the effective crenCAe) 2L5x3xリ4 LLB3 (two angles, long legs back-fo-buctk) A242 Steel PL 7/8" diameter bolts 3:4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The details of the principal stresses at a certain point in a steel member are as follows: Major…

A: Given - Major principal stress, σ1 = 180 N/mm2 (Tensile) Yields stress, σy = 240 N/mm2 To find -…

Q: 2. The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls.…

A: Length of bar, L =3mCross sectional area of bar, A=350mm2Initial temparature, t1 =20°CCoefficient of…

Q: Tensile strength became. . when * .cohesive of particles absent ten five zero

Q: The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table.…

A: Please refer explanationExplanation:Step 1: Step 2: Step 3: Step 4:

Q: 1.12 Tensile stress of 500MPA is applied on a steel rod of length 300mm. Determine the elongation in…

A: Given: Original length of rod, l = 300 mm Tensile stress, σ = 500 MPa Modulus of Elasticity, E = 200…

Q: The stee bar Al has a recanguar cross section Part A itis pin cornected al s ends, detemine the…

A: Solution-The load operating on the columns AB via the beam BC is denoted by.wL2=w×52.......L=5mThe…

Q: An aluminum alloy cylinder with a diameter of 76 mm and a height of 150 mm. is subjected to a…

Q: 3. The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

Q: 6. Value of Young's modulus of elasticity of steel if , Bulk modulus is 160 GPa and Poisson's ratio…

Q: The bending stresses on an element are: om 25,00 psi or= 21,667 psi. There is a stress raiser with…

A: Given:σm = 2500 psiσr = 21667 psiSy = 80000psiSu = 90000 psiSe = 40000 psiKf = 1.4

Q: 6. Value of Young's modulus of elasticity of steel if , Bulk modulus is 160 GPa and Poisson's ratio…

Q: Given data : Stress =4 N/mm2 Area=4 mm2 Find Tensile load

A: Given data, Stress = 4 N/mm2 Area = 4 mm2 Find :- Tensile Load

Q: Q- A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial…

A: Given data- Diameter d=60 mm, Length L=100 mm, Axial compressive force=40,000 kg, Bulk modulus =…

Q: A metal bar do in diameter and l, gage length failed under an axial tensile load of F. The final…

A: Engineering stress is the ratio of force applied and the initial cross-sectional area of the bar.…

Q: The bar MNOP rigid bar is pinned at N and connected to two vertical rods. Assuming that the bar was…

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

Q: What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the…

Q: Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads…

A: Est=200GPa Eal=70GPa Ebr=83GPa Overall deformation= 3mm

Q: THIS IS FOR EXTRA CREDIT. Determine (a) the equations of the shear and bending- moment curves for…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: Calculate Poisson's Ratio for a steel that has a modulus of elasticity E of 30,000,000 psi and a…

A: The given data is: Modulus of elasticity, E=30000000 psi Modulus of rigidity, G=11500000 psi

Q: (a) Tensile stress, (b) the axial linear strain,

A: Given the length of the steel bar L = 24 in diameter if the steel bar d = 0.625 in there fore…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

Q: tress in segment bronze and steel

A: Given data : Area for bronze segment (ABr)=700 mm2Area for steel segment (ASt)=800 mm2Force in…

Q: A bar of solid circular cross section is loaded in tension by forces P (see figure). P P | d L The…

A: Given data in question Length Diameter Modulus of Elasticity Allowable stress Elongation To find…

Q: What is the value of reduction factor of the beam, if

A: rcc:

Q: Problem- wwwwwwwww A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load…

A: Given- Steel bar length L=2 m=2000 mm, Width b=20 mm, Thickness t=15 mm, Tensile load P=30 kN,…

Q: A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the…

A: Given data Stress in x direction (σx) = 200 MPa E = 200 GPa μ = 0.3

Q: Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together…

Q: A steel column has the following properties: Modulus of elasticity, E = 200 GPa, yield strength,…

Q: A-36 steel has a modulus of elasticity of 250 GPa and Poisson ratio of v = 0.30. Determine the shear…

A: This question is related with solid mechanics . In this question we are provided with value of…

Question

Determine the nominal tensile strength based on the effective area (Ae). I am aware that the equation for Ae= Ag*U

Determine the nominal tensile strength bused un the
effective crenCAe)
2L5x3xリ4 LLB3
(two
angles, long legs
back-fo-buctk)
A242 Steel
PL
7/8" diameter bolts
3:4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Round off final ans, dont round off initial values
steel bar originally 200 mm long is pulled in tension with stress 150 MPa the magnitude of elastic modulus E IS 250 GPa, the magnitude of elongation is * O 0.3 mm O 0.6 mm O 1.2 mm O 0.75 mm
I need the answer as soon as possible
Determine the maximum tensile strength of the steel bar described by the following data Initial diameter = 12 mm Final diameter = 6.5 mm Initial length = 60 cm Final length = 86 cm Ultimate load = 5000 kgf
8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
I need the answer as soon as possible
If Poisson's ratio is 0.42, the Modulus of rigidity is 70.4225 GPa, and the bulk modulus is 416.66 GPa, then the elastic modulus of elasticity is (3 Points) 300 GPa 300 MPa 200 MPa None 200 GPa
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Compute the modulus of elasticity. and Compute the yield strength at a strain offset of 0.002.
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
Use the following Stress-Strain plots to answer the following questions (NOTE: These represent the SAME MATERIAL 400 300 200 100 0.00 0.05 0.1 0.15 0.2 0.25 0.3 0.35 Strain 375 300 225 150 75 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain Stress (MPa) Stress (MPa)
4