Determine the maximum stress in the frame of the 100kN punch press as shown in the figure. 15cm 36cm 3cm 4cm. 100 kN 100 kN

Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 15 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 21 ksi, determine the minimum diameter d₁ required for rod (1). F₂ (1) F₁ 1.023 in. 0.954 in. 0.682 in. 1.108 in. 0.585 in. F₂ B C d₁ -d₂

NEED ANSWER ASAP THANK YOU !!  A joint is made by gluing two plywood gussets of thickness t = 0.78 in to wood boards. Determine the shear stress for the glue (in psi) if the dimension b = 17.51 in and the applied force is P = 9857 lb. Round off the final answer to three decimal places.

(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.

(1) Given: B P=28 KN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm (3) Q R = 38 kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.

06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm

The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.

The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the resultant internal loadings at cross sections at point on the assembly. Express your answers, separated by commas, to four significant figures. V AZO NE=, VE =, ME = Submit Request Answer Part B Determine the resultant internal loadings at cross sections at point F on the assembly. Express your answers, separated by commas, to four significant figures. Np. Vp, Mp= Submit Provide Feedback VO ALO 63 12 Request Answer 1? kN, KN, KN-m kN, KN, KN-m D E 0.5 m 0.5 m 0.5 m B Im -1.5 m 2 m

NEED ANSWER ASAP, THANK YOU A joint is made by gluing two plywood gussets of thickness t = 0.53 inCHES to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 15.73 in and the applied force is P = 7988 lb. Round off the final answer to three decimal places.