300 mm C P 40 mm 60 mm B

Q: The direct stresses at a point in a material are 160N/mm2 (tensile) and 120N/mm2 (compressive).…

A: The principal stresses at any point in a body can be calculated using the formula given below as-…

Q: 43. A semi-circular arch with a radius of 1 m is subjected to a concentrated load of 2.8 kN at point…

A:

Q: A 60 mm- В 90 mm- 100 mm C 4 kN 80 mm D 140 mm

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: the normal and shearing

A: To determine the normal and shear stress .

Q: The couple M is applied to a beam of the cross section shown in a plane forming an angle b with the…

A: Given:The couple is the angle is

Q: At a point in a vertical cross-section of a beam there is a resultant stress of 75 MN/m2 , which is…

A: Given-At a point in a vertical cross-section of a beam there is a resultant stress of plane is…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: - 24 in.- D 10 in. B| C y

A:

Q: Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.89 in2 P =…

A:

Q: Determine the state of stress at point A of the rectangular post shown loaded with concentrated…

A: Ffgg

Q: The cantilever beam AB has a rectangular cross section of 150 × 200 mm. Knowing that the tension in…

A:

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: The couple M=126 kip-in. acts in a vertical plane and is applied to a beam oriented as shown.…

A: M = 126 kipTo find out :-The stress at point A

Q: 3. Draw each one of the infinitesimal elements A, B and C individually, and indicate the stress…

A: the cantilever beam as shown below with points given sectional area is hollow square as shown in…

Q: The split ring shown has an inner radius ₁0.6 in. and a circular cross section of diameter d= 0.8…

A:

Q: Problem 4: For the beam and loading shown: The forces and couples shown act on the axle of an…

A: For the beam and loading shown:   The forces and couples shown act on the axle of an automobile.…

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

A:

Q: Given the plane element shown which is an element acted upon by combined stresses. a. Use Mohr's…

A:

Q: 1) Determine the stress components acting on the inclined plane AB. 65 MPa /30 20 MPa

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16…

A:

Q: B The two rods AB and AC have diameters of 10 millimeters and 8 millimeters. Determine largest…

A:

Q: In the figure shown, assume that a 21.3-mm- diameter rivet joins the plates that are each 118 mm…

A: Given Data Diameter of riveted joint is :d=21.3 mm width of plates is : W=118 mm Bearing stress is…

Q: Knowing that the structural tube shown has a uniform wall thickness of 0.35 in., determine the…

A: In solid mechanics, the shear formula helps us to determine the critical shear stress in designing…

Q: 6 in. ااه 800 lb

A:

Q: A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A…

A:

Q: 2.) Solve for the normal stress of rod AB with a diameter of 10mm if the block has a mass of 40kgC…

A:

Q: Determine the principal stresses and the maximum shearing stress at point H. (Round the final…

A: At point H, loading will be as per following, M=600(2.5)=1500 lb-inT=600(2.5)=1500 lb-inP=2300 lb…

Q: Determine the length (in meters) of the shortest 2-mm diameter bronze wire, which can be twisted…

A: ,

Q: Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your…

A:

Q: Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of…

A: Given: Number of turns (n)=19turnsDiameter of the wire (d)=0.96inMean radius (r)=3.53inLoad…

Q: 4) The two-member frame is subjected to the distributed loadings shown. Determine the average normal…

A: Given data   Square section of 35 mm sides w = 8 kN/m Find the stress at sections a-a and b-b.

Q: Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of…

A: We have to solve above question determine shearing stress in a bronze helical spring

Q: The couple M is applied to a beam of the cross section shown in a plane forming an angle β with the…

A: Given:

Q: Determine the elongation in a helical steel spring composed of 22 turns of 21.37-mm-diameter wire on…

A:

Q: The cross-section of bar ABCD is made of a triangle with sides equal to 15 mm, 12 mm, and 10 mm.…

A:

Q: The control arm is subjected to the loading shown. Determine to the nearest the ¼-in. required…

A: Given data: - The distance between AC is LAC = 8 in. The distance between CB is LAC = 3 in. The…

Q: Determine the stress (in psi) in member AB if the cross-sectional area of the BD is 1.90 in2 P =…

A:

Q: The couple M acts in a vertical plane and is applied to a beam oriented as shown. Determine (a) the…

A: Given data as per the question M=15 kip.in. Iz=21.4 in4Iy=6.74  in4