Part A If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.

Part A If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-69.M Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be if the circular shank of the bolt pulled out from the head, a shearing action. Compute the shear stress in the head for this mode of failure if a force of 22.3 kN is applied. Applied force Shear area Reaction force on underside of head Cylindrical shear area 19.0 mm 8.00 mm -12.0 mm M12 x 1.75 thread
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
HOW TO SOLVE: Draw the FBD of one member Solve for the bearing force. Section one bold and solve internal forces. Solve for the normal and shear stress in the bolts. Solve for the bearing stress in the members due to the nuts. Solve for the bearing stress in the members due to bolts. ANSWERS: bearing stress of bolt= 7.96 MPa, T; shear stress of bolt= 13.78 MPa; bearing stress (max)= 18.04 MPa
Example 8 1-55: In the structure shown, an 8 mm diameter pin is used at A, and 12-mm- diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired. Top view k200 mm 180 mm 12 mm 8 mm B C B A B 20 mm 8 mm 8 mm 12 mm Front view Side view
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear stress in the bolts must be limited to 200 MPa, determine the minimum bolt diameter that may be used in the connection. 15.3 mm 13.5 mm 21.7 mm 25.2 mm 23.8 mm
Q1/ The yoke-and-rod connection is subjected to the load shown below. Determine to the nearest one millimeter (1) the required diameter of the steel pin A between the members and (2) the required diameter of the rods. Assume that the normal failure stress is 400 MPa and the shear failure stress is 240 MPa . Use factor of safety against failure in normal stress of 2.0 and factor of safety against failure in shear stress of 3.0. di 15 kN di 15 kN
5 Puan 800 N 45mm 800 N 9. The lapbelt assembly is to be subjected to a force of 800 N. Determine the required radius of the pin if the allowable tensile stress for the material is 20 MPa, allowable shear stress of glue is 15 MPa and allowable shear stress for the pin is 30 MPa. OA178 mm OB14.12 mm O D12.05 mm EE (Apolication/PubliclOnlineExam?examid=4718#
What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
Q1/ Find the minimum bolt diameter and the minimum thickness of each yoke that will support a load P = 14 kips without exceeding a shearing stress of 12 ksi and a bearing stress of 20 ksi.
Problem 5: At times in design, you would like to ensure that failure occurs in a specific part. For instance, in watch designs many components are stacked on top of one another due to the small space requirements. In this case if failure must occur, it is best that it happens in a gear that is easy to access. Using the maximum shear stress theory and only the stresses related to bending, determine the safety factors of the teeth on gears A, B, and C below. Each tooth can be assumed to be a rectangular cantilever beam with a point force at the end, the force can be determined using Torque = F x r. 0000 Gear B Gear C Gear A Torque on Shaft Gear Radius Tooth Length Tooth Height Tooth Thickness Gear A 10 N-mm 8.0 mm 1.5 mm 1.5 mm 0.5 mm Gear B 8 N-mm 3.0 mm 2.0 mm 1.5 mm 0.5 mm Gear C 6 N-mm 5.0 mm 1.5 mm 2.0 mm 0.8 mm Gear D Gear D 30 N-mm 10.0 mm 1.5 mm 1.5 mm Solve Material: Steel E =200 GPa Sy = 250 MPa
Two parts of a machine, both made from steel, are held together by 5 equally-spaced M6 x 1.0 grade 8.8 bolts that are uniformly tightened to provide a total initial clamping force of 23 kN in the members. Each bolt has a proof stress of 600 MPa, and a tensile area of 20.1 mm². The elasticities are such that the joint constant is 0.2. A uniform static tensile load of 12 kN is applied to the entire joint after it has been preloaded. What is the magnitude of the total clamping force in the joint after the application of the tensile load? Express your answer in units of kilonewtons.