Determine the load in kN that a 2mX2m floor slab will carry if the following loads are present: a. Slab is made of reinforced stone concrete b. A 25mm thick lightweight concrete fill on top. c. A suspended ceiling made of metal lath and gypsum plaster, and d. A 2.5m height wood stud frame (made of 2x4" wood) with plastering on both sides. Refer to the diagram below: 25mm 150mm 2m 2.5m 25mm thk lightweight concrete fill 2mx2m reinforced stone concrete slab suspended ceiling

Determine the load in kN that a 2mX2m floor slab will carry if the following loads are present: a. Slab is made of reinforced stone concrete b. A 25mm thick lightweight concrete fill on top. c. A suspended ceiling made of metal lath and gypsum plaster, and d. A 2.5m height wood stud frame (made of 2x4" wood) with plastering on both sides. Refer to the diagram below: 25mm 150mm 2m 2.5m 25mm thk lightweight concrete fill 2mx2m reinforced stone concrete slab suspended ceiling

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
Discuss Structural dead loads
a monolith floor framing plan is shown in the figure. the column are 300 mm square, girderes are 250 mm wide by 450 mm deep and slabs are 100 mm thick. the floor loads include floor finish of 0.77 kpa, ceiling system of 0.25 kpa, partition load of 1.0 kpa and live load of 4.8. bar centroid from the edge of the beam us 70mm. what is the total factored floor load?
Design an exterior slab panel of a two-way slab system. Panels are 20feet x 25feet. Column size is 12inch x 24inch. The beam size is 10inch x 20inch. Live load is 100psf. Wall thickness is 5inch, floor height is 10feet; doors and windows opening is 20%. The floor finish is 20psf.Given, f'c = 3.5ksi and fy = 60ksi;
The following is a floor plan for a 1200 sq ft reading room in a library (you can find the loading from the ASCE building load handout). The concrete columns are 25 ft in length and have an elastic modulus (E) of 3370 ksi. The concrete slab (γ = 150 pcf) is 7 inches thick. The beams which are directly supported by the columns are steel W18x86 sections. NOTE: Clearly the floor plan below is not drawn to scale. (a) Does this system represent one way or two way slab loading? (b) Calculate and draw the loading on beams A-C and B-C (include the self-weight of the beam)[answer in lbs/ft or kips/ft] (c) Draw the shear and bending moment diagram of beams A-C and B-C (assuming simply supported end conditions). Label moment and shear at the ends and midspan of the beam. (d) Calculate the loading demand on column C (neglect the self-weight of the columns) [answer in lbs or kips] NOTE: You can ignorethe reduced live load factor given in equation 1-1 ofthe textbook even though this column…
The following is a floor plan for a 1200 sq ft reading room in a library (you can find the loading from the ASCE building load handout). The concrete columns are 25 ft in length and have an elastic modulus (E) of 3370 ksi. The concrete slab (γ = 150 pcf) is 7 inches thick. The beams which are directly supported by the columns are steel W18x86 sections. NOTE: Clearly the floor plan below is not drawn to scale. (d) Calculate the loading demand on column C (neglect the self-weight of the columns) [answer in lbs or kips] NOTE: You can ignorethe reduced live load factor given in equation 1-1 ofthe textbook even though this column would satisfy KLLAT> 400 ft^2. (e) Will column C buckle if the ends are pinned(k = 1.0)? (f) If the deflection limits set forth by the ASCE building code are [in]less than L/360, does beam B-C pass? (note: Esteel= 29,000 ksi, Ix,beam= 1530 in^4)
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)
the load is 150kN at the center of the beam and the dimension of the beam is 6x6x24. compute for modulus of rupture
Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 18. Calculate the strain of the steel reinforcement
A rigid building structure has the following particulars: Dimensions: 10 m x 20 mx 16.6 m high Located in an area classified as exposure B. Is neither open nor partially closed. Risk category: I Wind is 120 km/h and acts on the wall with the higher dimension. What is the external wind pressure on the side wall? O a. formula: wind pressure = qGC₂ = (0.613K₁K₂tKalV²) X G X Cp -248 N/m² O b. -896 N/m² O c. -386 N/m² O d. -333 N/m²