36

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: The ∑ F proceeding in the couple is?

A: Brief concept- Couple- It is a pair of equal and opposite parallel forces. These two forces do not…

Q: The U-tube shown in figure (5), is filled with water and rotated about a vertical (0.15m) to the…

A: Given:-R=0.6mh=0.3mvertical axis = 0.15m to right of AGauge pressure at A=0To find:-Rotational speed…

Q: 40 fé = 3000psi %3D ダク 26" 14 14 fy = 6o ksi %3D 8#8 12 NWC PMa = ?

A: A beam with T section is given in the above question. The value of fc' and fy is provided. also the…

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: ments Collaborate 此片 Freak Out Slice Crop Horizontal Start New Sheet Sketch Sketch Sheets 5 LBS…

A:

Q: Draw (A.F.).(S.F.) &( B.M.) diagrams for the following problems: H 12t 5m 4m 2 1 3m 5m 4m 3m

A:

Q: 1.2.8. Please show all work, i got MA wrong.

A: Step 1: dear students yours questions is insufficient please full answer and missing the information…

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. + 2 A = O O…

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: What is Dutch (Deft) cone is consists of?

A: The cone penetration test (CPT) is a technique used to measure the geophysical characteristics of…

Q: 205, 406 ton=722 %3D How are Yoll tonne - 72 %31

A: Give that, Tonne is metric measure  1 TON  = 0.90718 tonne   TON is American unit

Q: "hat is the degree of indeterminacy of the given Tucture? a. -1 b. 0 С. 1 d. 2

A:

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: Explnation of EPDM.

A: The ethylene propylene diene monomer is abbreviated as EPDM.

Q: Describe Mohr’s Circle.

A: Mohr’s circle is defined as a two-dimensional graph which represents stresses at a point.

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: 4.157 Find the forces in members CD, DH, and HI.

A: The given figure is shown below:

Q: Y

A:

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: 1 Determine the moment of the Couple JKN IKN 1.75. 0.75m

A: Moment generated due to this couple = 1×0.75=0.75 KN.m

Q: is x correct?

A: Data Availabe: Asked: Centroid

Q: B Convert the following bearing from W.C.B TO QB 1. OA=22 30'N 2. OC = 327 24' N 3. OB = 170 12' N…

A: 1. OA= 22°30'N Reduced bearing of the line is N22°30'E

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.