determine the grain size using thefollowing equationGn100=nMM =M100Real lengthScale bar (written dimension) Use a 1 inch by 1 inch square from the following pictreTitle Lab#1Material steel1020Magnification 250 x Med Res100.000 μmMethod: HorizontalIntercepts: 47Length: 1.279mmGrainsize: 7.1113Ĉ

Given: Equation of the grain size: →n100=nMM1002 Where M is : →M=Real length Scale bar Because real…

Answered: determine the grain size using the…

Engineering

Mechanical Engineering

determine the grain size using the following equation n100=nM M = M 100 2 Real length Scale bar (written dimension)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: trength of metals and their alloys increases as grain size decreases. Find out the amount of…

A: From hall patch equation:σy=σ∞+kDHere,σy is the yield strength of grainD=Grain diameterσ∞=Yield…

Q: The effect of temperature on the crystallization of a material is given below. Calculate the…

A: Given is Effect of temperature on the crystallization of the material To determine…

Q: If a rod of single-crystal copper (FCC) is pulled in tension in the [210] direction (i.e. force…

Q: a) Problem 2: Calculate the number of atoms per unit cell for an fec lattice of copper (Cu) crystal.…

Q: On the basis of ionic charge and ionic radii given in Table 3.4, predict crystal structures for the…

Q: Based on the information in the table below answer the following questions Element Atomic radius…

A: The Hume-Rothery rules specify that the following properties must be similar for two atoms to mix to…

Q: Problem 4: The state of stress at a particular point in a structure is given below. 10 20 0 ¹-[20 =…

A: (a) σ3−20σ2−500σ+6000=0(b) charecterstic equation is satisfied it's condotion.(c) σ1=30 MPa ;…

Q: The attached photo shows the Young’s modulus of a cubic single crystal as a function of orientation.…

A: Write the vector notation of <110>, [100], [010] and [001]. Write the expression of the angle…

Q: Name the Crystallographic Direction and Show the Steps

A: Given

Q: 2 nswer: B End plate = 12 Fixed plate Tube (2) a Rod (1) Ib-in di b TB B

Q: b- An ASTM grain size determination is being made from a photomicrograph of a metal which has a…

A: Given data: Nm=64M=500 Need to determine the grain size number.

Q: Temperature C 1100+ 1000 Liquid 900. 800. 700 600 L+AL 500 400 (AI) 300+ 0 548.2°C (Al)+0 (Cu) ΑΙ 10…

A: Step 1: Given Data: Overall composition of alloy: 18.6 wt% Cu at 1000°C Initial masses:Al:…

Q: Vanadium has the Body-Centered Cubic (BCC) crystal structure shown in the figure below. The radius…

Q: What are the indices (h k e) of the plane shown below?

Q: The influence of grain size on the yield strength of metallic material is shown in the figure, what…

Q: Briefly explain the ASTM grain-size standard

A: ASTM grain size standard : The grain size measurement play an important role in improving the…

Q: According to Hall-Petch equation, the 1 point decreasing in grain size causes strengthening of…

A: Hall-Petch equation or Grain-boundary Strengthening predicts that when the grain size decreases…

Q: The random arrangement of atoms in a structure is known as crystalline structure. Select one: O True…

A: The basic structure of materials: The basic structure of a material is divided into two categories,…

Q: 3) Figure - 2 shows a round bar (Ø 40 mm) being used as a bracket to suport equipment attached as…

A: To find: The stress and strain in each bar, and also find the Poisson's ratio if diameter is…

Q: A half a plane of atoms are inserted into the crystal lattice is known as O Screw Dislocation O Edge…

Q: A laser emits light of frequency 851523504007150 Hz. What is the wavelength of the light in nm?…

A: Given data, f= 851523504007150 Hz. Speed of light c= 3*10⁸ m/s

Q: I need a clear step by step answer please

A: Grain size is the dimension of a grain in a polycrystalline metal. Grain size affects majority of…

Q: Gold has the Face-Centered Cubic (FCC) crystal structure. The edge length is a = 0.408 nm. What is…

A: Given data: Gold has FCC crystal structure. The edge length a=0.408 nm

Q: 0.5а 5a (1/3)a {110}

Q: Consider an iron single crystal with CCC crystal structure oriented in such a way that a tensile…

Q: Show the miller-bravais index for a HCP structure

A: Find The miller-bravais index for an HCP structure.

Q: question j620 Find the Miller indices of each crystallographic plane

A: Given

Q: During 650°C, the average grain diameter of a brass material was measured as a function of time, as…

Q: Draw the following directions and planes: (1 121), (10ī0), [2110], [0002]. Use the unit cells…

A: for solution refer below images.

Q: When a uniaxial tensile stress (of symmetry o/mmm) is applied to cubic crystal of symmetry m3m, what…

A: (a)

Q: Consider a dislocation condition as shown below. A) what is the strain state in the upper region and…

A: Dislocation in any crystal causes the stress generation in the crystal and nature of stress depend…

Q: Calculate the critical resolved shear stress (magnitude) in crystal if a stress of 100 MPa in the SP…

Q: A round rod made of 6061-T6 aluminum has a cross-sectional area of 42 mm². A 200 kN axial tensile…

Q: You are given three metal test samples, with the same chemical composition and differing grain…

Q: Determine the ASTM grain size number of a metal specimen if 25 grains per square inch are measured…

A: Find the grain size no.

Q: An external load caused tensile stress is imposed along the [001] of a BCC single crystal. The…

A: Solution: Given Data: [001] directionBCC crystal To Find: The angle between the direction of…

Q: Iron (Fe) has the Body-Centered Cubic (BCC) crystal structure. The edge length is a = 0.2864 nm.…

A: Answer: The linear density in (atmos/nm) along direction [0 1 1] is 2.47 atmos/nm.

Concept explainers

Solidification of metals

The term solidification indicates the conversion of material from the state of liquid to the state of solid. The solid-state is more compact and rigid than liquid, and the solidification indicates the transformation of material from a random state to a more compact and crystalline form. The point at which dendrite formation in liquid starts taking place is referred to as the solidification point.

Question

determine the grain size using the
following equation
G
n100=nM
M =
M
100
Real length
Scale bar (written dimension)

Use a 1 inch by 1 inch square from the following pictre
Title Lab#1
Material steel1020
Magnification 250 x Med Res
100.000 μm
Method: Horizontal
Intercepts: 47
Length: 1.279mm
Grainsize: 7.111
3
Ĉ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a dislocation condition as shown below. A) what is the strain state in the upper region and B) how would addition of small impurity atoms in the region indicated by "*"s change it? oooooo OOOOO DO Select one: a. Compressive, would reduce compressive strain O b. Tensile, would decrease tensile strain O C. Compressive, would increase compressive strain Od. Tensile, would increase tensile strain Oe. Shear, would increase compressive strain
t A crystalline grain of Iron is oriented so that a tensile stress of 10 MPa is applied along the [101] direction. What is the resolved shear stress in [110] on the (101) ?
Who is the defect responsible for the phenomenon of slipping . vibration defects line defects (dislocation) O point defects vacancy defects are produced in the crystal lattice by . * dislocation in along line screw dislocation O thermal vibration grain boundaries an example of planer defects volume defects linear defects point defects
Consider an iron single crystal with CCC crystal structure oriented in such a way that a tensile stress is applied to the along one direction [010]. a) Calculate the shear stress resolved along a plane (110) and a direction when a tensile stress of 52 MPa is applied. The normal to the slip plane forms 45° with traction direction. the direction of slip forms 55º with the traction direction. b) If the slip occurs in one plane (110) and in one direction and the critical resolved shear stress is 30 MPa, calculate the magnitude of tensile stress that must be applied to initiate the flow.
Material science question
Find the Miller indices of the direction shown below. Show all steps and working. Use the correct type of bracket and bar notation for negative indices DL 1/2 1/4 a
Please help me with this if u cant do full skip it ill dislike, ill like for full answer its easy please
If ß-Sn, a tetragonal crystal (point group 4/mmm, a = 0.583 nm, and c = 0.318 nm) is subject to a tensile stress of 63 MPa along [100] and to a shear stress of 18 MPa on the (100) plane in the [010] direction. Determine: a) the tensile stress normal to (110), and b) the shear stress on the (110) plane in the [1-10] direction.
Please show all the work. Material science question, Don't use chatgpt for this question.
Q1.) Consider the unit cell of Mg as shown below : Beskou die Mg eenheidsel hieronder Mg HCP structure HDG struktuur Atomic radius 0.160nm Atoom radius Atomic weight Atoommassa c/a ratio / verhouding 24.31g/mol 1.624 НСР a) Calculate the lattice parameter of this unit cell; Bereken die roosterafmeting van die eenheidsel
The following are methods used for grain size determination (Choose all that apply) Linear analysis ASTM method Point counting Intercept method
I need an answer in half an hour