Determine the friction force at the surface of contact. X = 117N Y = 54N W = Y Ms = 0.9 Mk = 0.6 %3D

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

A:

Q: A vinyl [E = 2.80 GPa; v = 0.41] block with width b = 50 mm, depth d = 100 mm, and height h = 270 mm…

A: E = 2.8 GPa = 2.8 × 103 N/mm2Poisson's ratio (μ) = 0.41Determine the change in the depth dimension…

Q: Which stress element below correctly shows the normal and stress at point X? M T A G B D H Write the…

A:

Q: A steel cylinder is enclosed in a bronze sleeve, both simultaneously supports a vertical compressive…

A:

Q: 200 MPa 500 MPa 350 MPa

A: Please refer the attached image for complete solution. THANK YOU.

Q: An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein…

A:

Q: The steel rod is stress-free before the axial loads P1 =169 kN and P2 = 88 kN are applied to the…

A: calculate the axial force in each segment after the loads are applied.

Q: Determine principal stress

A: Given  Normal stress X = -10MPa Normal Stress Y = -3 MPa Shear stress = -2MPa   To find Principal…

Q: Determine the stress of the compression steel. 200 60 20mm 450 32mm 60 A 95.64 B 40.78 4.78 90.858

A:

Q: A P Front view ---160 mm What is the stress in bar BD if P = 4 kips? B D 12

A: Given: P=4kips

Q: The axially loaded steel material shown below has E = 29.000 ksi and vitel =0.30. Assuming that e, =…

A: As per Bartleby policy i can answer  only one question at a time. Please upload other questions…

Q: a. The value of x from locating the neutral axis using Qtop Qbot in mm is [Select] b. The value of…

A: Answer  (a) Consider 'x is a location of Neutral axis from the top as shown below Equate Qtop =…

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the…

A: Determine the magnitude of the force P for which the tensile stress in rod AB has the same magnitude…

Q: A flat steel bar, 27 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so…

A:

Q: 1. Determine the nominal load P that will cause failure of the beam shown below. As part of your…

A:

Q: XN W = 200 N My = 0.3 uk= 0.2 1. Determine the normal force between the crate and the surface 2.…

A:

Q: Determine the deflection at the end of the overhang by conjugate beam method or Castigliano's…

A:

Q: -0/02 -400 m

A:

Q: 11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are…

A: Applied load (P)=12000lb D=4in d=3 in Thickness (t)=3/8 in

Q: DETERMINE THE STABILITY, DETERMINANCY AND DEGREE OF INDETERMINANCY.

A: Ds=m+R-2j where m=number of members R=support reaction j=number of joints

Q: A base line was measured with a steel tape of designated length 30 m at 20°C at a pull of 100 N. The…

A:

Q: The height of the capillary rise of water increases as particle diameter increases True O False O…

A:

Q: The plate of thickness, t 5 mm, is loaded with the following stress; oy = 100 MPa, o, = -60 MPa, E =…

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A: As per guidelines we are supposed to answer only one question. Kindly repost other questions as a…

Q: Determine principal  stress

A:

Q: If the block is 1000kg, determine the value of frictional force if P is equal to 3200N.…

A: First ascertain that whether the block will be stationary or in motion under the action of applied…

Q: How to make a effective stiffness matrix for this figure?

A: The free body diagram of the given structure is:

Q: d= 50mm T= 1 KN-W -5KN 500mm asomm 6KN A Find all stresses: axial, torsion, and shear Makes stress…

A:

Q: Derive the stiffness matrix and Derive the kinema tic eyuetien

A: To perform out a precise investigation an structural engineer should decide data, for example,…

Q: 30 F 20° B.

A: Draw the free body diagram of block B.

Q: - 25-mm-diameter In a standard tensile test a steel rod of 25-mm diameter is subjected to a tension…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.