Determine the force in member CG. Assume F₁ = 6 kips, F₂ = 7 kips, F3 = 1 A H 10' G B 10'

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: 10 + 5x < 6+3x

A:

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: Find KN derivation Y = K m²³

A: We have to prove that the unit of unit weight is kN/m3.

Q: CEM IV 42.5 N: Define what each word/number/letter is?

A: 1.CEM-  CEM means CEMENT .Cement is the binding material from which concrete is prepared. Cement act…

Q: Give real life examples of Mohr's Circle

A: Brief concept introduction- Mohr's Circle- It gives the relationship between the normal and shear…

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: 12" 6* 12" MATHalino.com

A:

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: wrong given, pls. answer

A: Given: Span= 10m, axle loads as shown in figure

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: Y

A:

Q: 4 cm 0 2 י 5 cm 4 567 Value: cm 10 5 150 Value: mm 0 140

A: There are two scales, and the values shown on the two scales are required.One is the main scale and…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.