Determine the flow rate required to produce 25 MW of shaft power from a steam turbine in which the steam enters at 10 MPa and 720 K and exits at 5 kPa for the following cases: (a) an ideal turbine and (b) a turbine with an isentropic efficiency of 96%. w=25 MW P; =10 MPa 1 T=720 K Pz=5 kPa

Determine the flow rate required to produce 25 MW of shaft power from a steam turbine in which the steam enters at 10 MPa and 720 K and exits at 5 kPa for the following cases: (a) an ideal turbine and (b) a turbine with an isentropic efficiency of 96%. w=25 MW P; =10 MPa 1 T=720 K Pz=5 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Task (4) Critically compare how the changes of the heat transfer efficiency will affect the lifetime of the turbine.
In a Parson turbine running at 1500 RPM the available enthalpy drop for expansion is 62.8 kJ/kg. If the mean diameter of the rotor is 90 cm, find the number of rows of moving blades required. Assume stage efficiency of 75%. Blade outlet angle is 20° and speed ratio is 0.7.
Consider an adiabatic steam turbine. The inlet temperature of the steam to the turbine is 600 oC and the pressure is 6Is MPa. The steam has a mass flow rate of 2.5 kg / s and the exit pressure from the turbine is 45 kPa. Turbinekinetic and potential energies in it are neglected. 91% of the adiabatic efficiency of the turbineis known to be. According to this;a. Find the exit temperature of the steam from the turbine.b. Find the output power of the turbine.c. Draw the system schematically and show it on the T-s diagram.
A turbine receives steam at 8.8 MPa, 510OC and exhaust it at 0.175 MPa. (a) For the ideal Rankine, determine the work, steam rate, thermal efficiency, and mean effective pressure. (b) For the actual engine, the brake engine efficiency is 89%; the driven generator efficiency is 96% and the rated output of the generator is 32 MW. Estimate the enthalpy and quality (or temperature) of the exhaust. Compute the combined work, combined heat rate, and the total throttle flow for the rated power. Please answer a, b and c. Thanks you
A turbine receives steam at 10 MPa, 6000C and exhaust it at 0.2 MPa. (a) for the ideal Rankine engine, determine the work, steam rate, thermal efficiency, and means effective pressure. (b) for the actual engine,the brake engine efficiency is 84%; the driven generator efficiency is 93% and the rated output of the generator is 30 MW. Estimate the enthalpy ang quality (or temperature) of the exhaust..Compute the combined work, combined heat rate, and the total throttle flow for the rated power. Don't answer the given problem, just give me the schematic diagram andT-S diagram of the given problem
Steam is supplied to a fully loaded 100 hp turbine at 200 psia with u1 = 1160BTU/lb, V1 = 2.6 ft3/lb and v1 = 380 ft/s. Exhaust is at 1.1 psia with U2 = 900 BTU/lb., V2 = 1200 ft/s. The heat loss from the steam in the turbine is 10.5 BTU.Ib.Neglect the potential energy change and determine:a.the work per lb steamb. the steam flow rate in Ib/hour
A net of 2500 kW is needed from a gas turbine engine. Air enters the compressor section at 13.005kPag, 315K. The turbine sections receive the hot gas at 1905 K. Draw the (a) P-V and T-S diagrams. Find (b) air flowand, (c) thermal efficiency. (d) For the maximum work, what should be the temperature of the air leaving thecompressor. Consider rp = 11, k = 1.35 and R = 260.078 J/kgm-K.
Q2Air enters an insulated turbine at 50°C, and exits the turbine at - 30°C, 100 kPa.The isentropic turbine efficiency is 70% and T1=50C V=20L/s the inlet volumetric flow rate is 20 L/s. What is the turbine Air turbine inlet pressure and the turbine power output? T2=-30C.P2=100kpa
What should happen to Qnet, ΔKE, and ΔPE to have a maximum Wnet done by a turbine??
Problem 5 Refer to the steam power plant below and determine the following: ii. i. Specific enthalpy at the steam turbine inlet Specific enthalpy at the steam turbine exit Density at the pump entrance iii. Wn P. 20 kPa T Tat@20kPa-5.6°C W Pump Qn Boler Condenser Qout Steam Turbine P= 8MPa T= 450°C Wout P▪ 20 kPa s *6.5579 kg K
Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The pressure at stage-2 and stage-3 so that the compression work is minimum? b) The compression work in each stage and the total compression work? c) The outlet air temperature from each stage's cylinder? d) The amount of heat transferred to each intercooler? e) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?
: Determine the total turbine power output ? in the adiabatic turbine receives the water at (15000 kPa), (873 K) for mass flow rate of (100 kg/s), In the midst part (20 kg/s) is withdrawn at (2 MPa), (350°C), and the rest outlets the turbine at pressure (75 kPa), and (95 percent )quality.Neglecting the changes in kinetic energy,